Is a fire-rated wall also soundproof?

It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.

Do you stand behind your fire-rated work in Keswick Area?

Yes. We install to code and walk the Keswick Area job with you, and if something is not right we come back and make it right.

How do I know which rated assembly my Keswick Area project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Where is fire-rated drywall required?

The standard Keswick Area fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Keswick Area project needs.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Fire-Rated Drywall Keswick Area Edmonton | Type X Board

Fire-rated drywall in Keswick Area, installed to code

In Keswick Area the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Keswick Area we install fire-rated drywall to code and finish it clean. Keswick Area is this established Edmonton community where reno, repair and ceiling drywall are common, so fire-rated work here is common on garages and suites. We cover Keswick Area, Chappelle Area, Heritage Valley Town Centre Area, Mcconachie Area and Edmonton, 7 days a week.

Party walls and legal-suite separations
Finished clean and inspection-ready
Joints taped as part of the rated assembly, not just for looks
Furnace and mechanical room enclosures
Rated assemblies installed and sealed correctly
Garage-to-house firewall separations
Garage ceilings and garage-to-house separations in Keswick Area

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Keswick Area assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Fire-rated drywall in a Keswick Area garage ceiling

The most common one we do

Where Keswick Area living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Keswick Area depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Fire-rated garages, suites and party walls in Keswick Area

Garage firewalls

The most common fire-rated job in Keswick Area is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Keswick Area homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Keswick Area garages where storage access was cut in afterwards and never addressed.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Keswick Area drawings and tell you if what is on site does not match it.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Keswick Area Edmonton

Free quote

We come out to your Keswick Area Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Keswick Area Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Keswick Area Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Keswick Area Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Keswick Area Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Keswick Area Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Keswick Area Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Keswick Area Edmonton

Fire-Rated Drywall Keswick Area Edmonton: your questions answered

Is a fire-rated wall also soundproof?: It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.
Do you stand behind your fire-rated work in Keswick Area?: Yes. We install to code and walk the Keswick Area job with you, and if something is not right we come back and make it right.
How do I know which rated assembly my Keswick Area project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Where is fire-rated drywall required?: The standard Keswick Area fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Keswick Area project needs.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Keswick Area Edmonton

Fire-rated drywall in Keswick Area, installed to code