Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Kenilworth ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Will it pass inspection in Kenilworth?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Kenilworth separation passes inspection.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Kenilworth garages where storage access was cut in afterwards and never addressed.

Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Fire-Rated Drywall Kenilworth Edmonton | Type X Board

Rated separations in Kenilworth that pass inspection the first time

A fire-rated wall is not a board, it is an assembly. In Kenilworth that means the specified board thickness and type, the specified stud and screw spacing, taped joints, and every penetration firestopped. Miss any one of those and the rating is not there, whatever the board says on the back.

Kenilworth coverage — we come to you
Garage ceilings and garage-to-house separations in Kenilworth
Finished clean and inspection-ready
Garage-to-house firewall separations
Penetrations firestopped before the finish goes on
Type X board to the assembly on the drawings
Party walls between units

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Kenilworth assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Kenilworth drywall in context

About Kenilworth

Kenilworth lies in the City's southeast, immediately north of the vibrant Whyte Avenue.

What we see in Kenilworth

In Kenilworth the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Kenilworth assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Our Kenilworth fire-rated drywall process, step by step

Right board, right build-up

In Kenilworth we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Kenilworth separation the inspector approves and the eye approves too.

Finishing a rated wall in Kenilworth without compromising it

Rated first, pretty second

Taping on a rated assembly in Kenilworth does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Kenilworth garages where storage access was cut in afterwards and never addressed.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Kenilworth build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Kenilworth Edmonton

Free quote

We come out to your Kenilworth Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Kenilworth Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Kenilworth Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Kenilworth Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Kenilworth Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Kenilworth Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Kenilworth Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Kenilworth Edmonton

Fire-Rated Drywall Kenilworth Edmonton: your questions answered

Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Kenilworth ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
Will it pass inspection in Kenilworth?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Kenilworth separation passes inspection.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Kenilworth garages where storage access was cut in afterwards and never addressed.
Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Kenilworth Edmonton

Rated separations in Kenilworth that pass inspection the first time