Do you install fire-rated drywall in Jackson Heights?

Yes — fire-rated drywall in Jackson Heights is part of our regular work, and we are usually booked within the week. We also cover Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Jackson Heights garage ceiling and a living room do not need the same finish level.

Can you finish the fire-rated board too?

Yes — your Jackson Heights separation passes code and looks properly finished, ready for paint.

Do you stand behind your fire-rated work in Jackson Heights?

Yes. We install to code and walk the Jackson Heights job with you, and if something is not right we come back and make it right.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Jackson Heights ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Fire-Rated Drywall Jackson Heights Edmonton | Type X Board

Fire-rated drywall in Jackson Heights, installed to code

Most fire-rated work we do in Jackson Heights is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Garage-to-house firewall separations
Jackson Heights coverage — we come to you
Joints taped as part of the rated assembly, not just for looks
Party walls and legal-suite separations
Type X fire-rated board to code in Jackson Heights
Furnace and mechanical room enclosures
Penetrations firestopped before the finish goes on

What makes drywall fire-rated in Jackson Heights

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Jackson Heights we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

Jackson Heights drywall in context

About Jackson Heights

Jackson Heights is named in honour of Annie B.

What we see in Jackson Heights

In Jackson Heights the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Jackson Heights. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

What affects the cost of fire-rated drywall in Jackson Heights?

Area and assembly

The cost in Jackson Heights depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Jackson Heights rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Jackson Heights

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Jackson Heights project passes the first time.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Jackson Heights are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Jackson Heights build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Jackson Heights drawings and tell you if what is on site does not match it.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Jackson Heights Edmonton

Free quote

We come out to your Jackson Heights Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Jackson Heights Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Jackson Heights Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Jackson Heights Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Jackson Heights Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Jackson Heights Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Jackson Heights Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Jackson Heights Edmonton

Fire-Rated Drywall Jackson Heights Edmonton: your questions answered

Do you install fire-rated drywall in Jackson Heights?: Yes — fire-rated drywall in Jackson Heights is part of our regular work, and we are usually booked within the week. We also cover Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Jackson Heights garage ceiling and a living room do not need the same finish level.
Can you finish the fire-rated board too?: Yes — your Jackson Heights separation passes code and looks properly finished, ready for paint.
Do you stand behind your fire-rated work in Jackson Heights?: Yes. We install to code and walk the Jackson Heights job with you, and if something is not right we come back and make it right.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Jackson Heights ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Jackson Heights Edmonton

Fire-rated drywall in Jackson Heights, installed to code