What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Where is fire-rated drywall required?

The standard Hillview fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Hillview project needs.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

How do I know which rated assembly my Hillview project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Will it pass inspection in Hillview?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Hillview separation passes inspection.

Do you stand behind your fire-rated work in Hillview?

Yes. We install to code and walk the Hillview job with you, and if something is not right we come back and make it right.

Fire-Rated Drywall Hillview Edmonton | Type X Board

Fire-rated drywall in Hillview, installed to code

In Hillview the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Hillview we install fire-rated drywall to code and finish it clean. Hillview is an Mill Woods and Meadows community with a mix of older homes and newer builds, so fire-rated work here is common on garages and suites. We cover Hillview, Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows, 7 days a week.

Rated assemblies installed and sealed correctly
Party walls between units
Type X fire-rated board to code in Hillview
Finished clean and inspection-ready
Garage-to-house firewall separations
Furnace and mechanical room enclosures
Penetrations firestopped before the finish goes on

Where Hillview homes usually need rated board

The four common places

Most rated drywall in Hillview houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Hillview project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Hillview drywall in context

About Hillview

Hillview is located immediately to the north of the Grey Nuns Community Hospital.

What we see in Hillview

In Hillview the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Hillview wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Hillview drawings and tell you if what is on site does not match it.

Fire-rated garages, suites and party walls in Hillview

Garage firewalls

The most common fire-rated job in Hillview is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Hillview homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Fire-rated drywall in a Hillview garage ceiling

The most common one we do

Where Hillview living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

What makes drywall fire-rated in Hillview

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Hillview we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Hillview Edmonton

Free quote

We come out to your Hillview Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Hillview Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Hillview Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Hillview Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Hillview Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Hillview Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Hillview Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Hillview Edmonton

Fire-Rated Drywall Hillview Edmonton: your questions answered

What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Where is fire-rated drywall required?: The standard Hillview fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Hillview project needs.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
How do I know which rated assembly my Hillview project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Will it pass inspection in Hillview?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Hillview separation passes inspection.
Do you stand behind your fire-rated work in Hillview?: Yes. We install to code and walk the Hillview job with you, and if something is not right we come back and make it right.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Hillview Edmonton

Fire-rated drywall in Hillview, installed to code