How do I know which rated assembly my Hairsine project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Do you install fire-rated drywall in Hairsine?

Yes — fire-rated drywall in Hairsine is part of our regular work, and we are usually booked within the week. We also cover Balwin, Bannerman, Belmont and Northeast.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Hairsine garage ceiling and a living room do not need the same finish level.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Do you stand behind your fire-rated work in Hairsine?

Yes. We install to code and walk the Hairsine job with you, and if something is not right we come back and make it right.

Fire-Rated Drywall Hairsine Edmonton | Type X Board

Type X board in Hairsine for garages, suites and mechanical rooms

No shortcuts on Hairsine fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Hairsine we install fire-rated drywall to code and finish it clean. Hairsine is an established south Edmonton community of 1960s-70s homes where ceiling stipple, settling cracks and dated texture are common, so fire-rated work here is common on garages and suites. We cover Hairsine, Balwin, Bannerman, Belmont and Northeast, 7 days a week.

Garage-to-house firewall separations
Finished clean and inspection-ready
Hairsine coverage — we come to you
Furnace and mechanical room enclosures
Type X fire-rated board to code in Hairsine
Type X board to the assembly on the drawings
Party walls between units

Fire-rated garages, suites and party walls in Hairsine

Garage firewalls

The most common fire-rated job in Hairsine is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Hairsine homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Hairsine drywall in context

About Hairsine

Hairsine was named for the first mayor of the town of Beverly and includes the Victoria Trail, which once led to the Old Victoria Settlement.

What we see in Hairsine

In Hairsine the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Where Hairsine homes usually need rated board

The four common places

Most rated drywall in Hairsine houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Hairsine project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Hairsine assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Why Hairsine homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Hairsine we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Hairsine and Northeast, 7 days a week. Fixed pricing on free Hairsine quotes, a clean site and a guarantee on the work. When an Hairsine job is not right, we make it right — on us.

Our Hairsine fire-rated drywall process, step by step

Right board, right build-up

In Hairsine we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Hairsine separation the inspector approves and the eye approves too.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Hairsine depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Hairsine Edmonton

Free quote

We come out to your Hairsine Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Hairsine Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Hairsine Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Hairsine Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Hairsine Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Hairsine Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Hairsine Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Hairsine Edmonton

Fire-Rated Drywall Hairsine Edmonton: your questions answered

How do I know which rated assembly my Hairsine project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Do you install fire-rated drywall in Hairsine?: Yes — fire-rated drywall in Hairsine is part of our regular work, and we are usually booked within the week. We also cover Balwin, Bannerman, Belmont and Northeast.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Hairsine garage ceiling and a living room do not need the same finish level.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
Do you stand behind your fire-rated work in Hairsine?: Yes. We install to code and walk the Hairsine job with you, and if something is not right we come back and make it right.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Hairsine Edmonton

Type X board in Hairsine for garages, suites and mechanical rooms