My Greenview garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Do you stand behind your fire-rated work in Greenview?

Yes. We install to code and walk the Greenview job with you, and if something is not right we come back and make it right.

Will it pass inspection in Greenview?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Greenview separation passes inspection.

How do I know which rated assembly my Greenview project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Greenview garages where storage access was cut in afterwards and never addressed.

Fire-Rated Drywall Greenview Edmonton | Type X Board

Fire-rated drywall in Greenview, installed to code

Where code requires it in Greenview, fire-rated board is mandatory: garage-to-house separations, suites and party walls take Type X in a rated assembly — for inspection and for safety. In Greenview we install fire-rated drywall to code and finish it clean. Greenview is an Mill Woods and Meadows community with a mix of older homes and newer builds, so fire-rated work here is common on garages and suites. We cover Greenview, Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows, 7 days a week.

Rated assemblies installed and sealed correctly
Penetrations firestopped before the finish goes on
Finished clean and inspection-ready
Greenview coverage — we come to you
Garage ceilings and garage-to-house separations in Greenview
Basement legal-suite fire separations
Party walls between units

What happens when an assembly is altered later

Every future trade is a risk

A rated Greenview wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

Greenview drywall in context

About Greenview

One of the 27 Mill Woods neighbourhoods -- and highlighted by some of the area's most attractive homes -- Greenview's development dates mostly to the 1970s and 80s.

What we see in Greenview

In Greenview the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Greenview assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Where Greenview homes usually need rated board

The four common places

Most rated drywall in Greenview houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Greenview project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Why Greenview homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Greenview we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Greenview and Mill Woods and Meadows, 7 days a week. Fixed pricing on free Greenview quotes, a clean site and a guarantee on the work. When an Greenview job is not right, we make it right — on us.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Greenview build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Greenview depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Greenview Edmonton

Free quote

We come out to your Greenview Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Greenview Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Greenview Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Greenview Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Greenview Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Greenview Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Greenview Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Greenview Edmonton

Fire-Rated Drywall Greenview Edmonton: your questions answered

My Greenview garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Do you stand behind your fire-rated work in Greenview?: Yes. We install to code and walk the Greenview job with you, and if something is not right we come back and make it right.
Will it pass inspection in Greenview?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Greenview separation passes inspection.
How do I know which rated assembly my Greenview project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Greenview garages where storage access was cut in afterwards and never addressed.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Greenview Edmonton

Fire-rated drywall in Greenview, installed to code