Where is fire-rated drywall required?

The standard Glenwood fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Glenwood project needs.

How do I know which rated assembly my Glenwood project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Will it pass inspection in Glenwood?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Glenwood separation passes inspection.

Can you finish the fire-rated board too?

Yes — your Glenwood separation passes code and looks properly finished, ready for paint.

Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Do you stand behind your fire-rated work in Glenwood?

Yes. We install to code and walk the Glenwood job with you, and if something is not right we come back and make it right.

Fire-Rated Drywall Glenwood Edmonton | Type X Board

Type X board in Glenwood for garages, suites and mechanical rooms

Most fire-rated work we do in Glenwood is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Party walls and legal-suite separations
Joints taped as part of the rated assembly, not just for looks
Type X board to the assembly on the drawings
Party walls between units
Garage-to-house firewall separations
Garage ceilings and garage-to-house separations in Glenwood
Basement legal-suite fire separations

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Glenwood. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

Glenwood drywall in context

About Glenwood

Glenwood is a large neighbourhood in the City's west end, and represents both residential and commercial land uses.

What we see in Glenwood

In Glenwood the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Glenwood build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

What happens when an assembly is altered later

Every future trade is a risk

A rated Glenwood wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Glenwood garages where storage access was cut in afterwards and never addressed.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Glenwood drawings and tell you if what is on site does not match it.

Our Glenwood fire-rated drywall process, step by step

Right board, right build-up

In Glenwood we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Glenwood separation the inspector approves and the eye approves too.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Glenwood Edmonton

Free quote

We come out to your Glenwood Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Glenwood Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Glenwood Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Glenwood Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Glenwood Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Glenwood Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Glenwood Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Glenwood Edmonton

Fire-Rated Drywall Glenwood Edmonton: your questions answered

Where is fire-rated drywall required?: The standard Glenwood fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Glenwood project needs.
How do I know which rated assembly my Glenwood project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Will it pass inspection in Glenwood?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Glenwood separation passes inspection.
Can you finish the fire-rated board too?: Yes — your Glenwood separation passes code and looks properly finished, ready for paint.
Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.
Do you stand behind your fire-rated work in Glenwood?: Yes. We install to code and walk the Glenwood job with you, and if something is not right we come back and make it right.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Glenwood Edmonton

Type X board in Glenwood for garages, suites and mechanical rooms