Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Can you finish the fire-rated board too?

Yes — your Fulton Place separation passes code and looks properly finished, ready for paint.

Is a fire-rated wall also soundproof?

It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.

Where is fire-rated drywall required?

The standard Fulton Place fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Fulton Place project needs.

Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Fire-Rated Drywall Fulton Place Edmonton | Type X Board

Fire-rated drywall in Fulton Place, installed to code

Most fire-rated work we do in Fulton Place is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Penetrations firestopped before the finish goes on
Rated assemblies installed and sealed correctly
Party walls and legal-suite separations
Joints taped as part of the rated assembly, not just for looks
Garage-to-house firewall separations
Fulton Place coverage — we come to you
Garage ceilings and garage-to-house separations in Fulton Place

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Fulton Place are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Fulton Place drywall in context

About Fulton Place

Named for the creek which runs through the ravine on its west boundary, Fulton Place lies east of the downtown core and developed in the 1950s.

What we see in Fulton Place

In Fulton Place the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Fulton Place depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Fire-rated drywall in a Fulton Place garage ceiling

The most common one we do

Where Fulton Place living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

Where Fulton Place homes usually need rated board

The four common places

Most rated drywall in Fulton Place houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Fulton Place project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Our Fulton Place fire-rated drywall process, step by step

Right board, right build-up

In Fulton Place we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Fulton Place separation the inspector approves and the eye approves too.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Fulton Place assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Fulton Place Edmonton

Free quote

We come out to your Fulton Place Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Fulton Place Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Fulton Place Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Fulton Place Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Fulton Place Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Fulton Place Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Fulton Place Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Fulton Place Edmonton

Fire-Rated Drywall Fulton Place Edmonton: your questions answered

Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Can you finish the fire-rated board too?: Yes — your Fulton Place separation passes code and looks properly finished, ready for paint.
Is a fire-rated wall also soundproof?: It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.
Where is fire-rated drywall required?: The standard Fulton Place fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Fulton Place project needs.
Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Fulton Place Edmonton

Fire-rated drywall in Fulton Place, installed to code