Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Do you install fire-rated drywall in Ermineskin?

Yes — fire-rated drywall in Ermineskin is part of our regular work, and we are usually booked within the week. We also cover Aspen Gardens, Bearspaw, Blue Quill and Whitemud.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Ermineskin garages where storage access was cut in afterwards and never addressed.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Can you finish the fire-rated board too?

Yes — your Ermineskin separation passes code and looks properly finished, ready for paint.

Fire-Rated Drywall Ermineskin Edmonton | Type X Board

Fire-rated drywall in Ermineskin, built as a complete assembly

In Ermineskin the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Ermineskin we install fire-rated drywall to code and finish it clean. Ermineskin is an Whitemud community with a mix of older homes and newer builds, so fire-rated work here is common on garages and suites. We cover Ermineskin, Aspen Gardens, Bearspaw, Blue Quill and Whitemud, 7 days a week.

Garage-to-house firewall separations
Finished clean and inspection-ready
Rated assemblies installed and sealed correctly
Type X board to the assembly on the drawings
Type X fire-rated board to code in Ermineskin
Party walls between units
Joints taped as part of the rated assembly, not just for looks

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Ermineskin. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

One-hour and two-hour assemblies

What the number means

A rating is how long a tested assembly resisted fire under laboratory conditions, not a guarantee about your Ermineskin house. One hour is the common residential separation; two hour appears between units in some buildings.

Why it changes the build

A two-hour assembly is usually two layers of board with offset joints, which changes material, labour and thickness. It is specified on the drawings and it is not something to substitute down.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Ermineskin depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Ermineskin build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Ermineskin assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Why Ermineskin homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Ermineskin we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Ermineskin and Whitemud, 7 days a week. Fixed pricing on free Ermineskin quotes, a clean site and a guarantee on the work. When an Ermineskin job is not right, we make it right — on us.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Ermineskin Edmonton

Free quote

We come out to your Ermineskin Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Ermineskin Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Ermineskin Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Ermineskin Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Ermineskin Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Ermineskin Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Ermineskin Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Ermineskin Edmonton

Fire-Rated Drywall Ermineskin Edmonton: your questions answered

Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
Do you install fire-rated drywall in Ermineskin?: Yes — fire-rated drywall in Ermineskin is part of our regular work, and we are usually booked within the week. We also cover Aspen Gardens, Bearspaw, Blue Quill and Whitemud.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Ermineskin garages where storage access was cut in afterwards and never addressed.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Can you finish the fire-rated board too?: Yes — your Ermineskin separation passes code and looks properly finished, ready for paint.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Ermineskin Edmonton

Fire-rated drywall in Ermineskin, built as a complete assembly