Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Can you finish the fire-rated board too?

Yes — your Ebbers separation passes code and looks properly finished, ready for paint.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

How do I know which rated assembly my Ebbers project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Where is fire-rated drywall required?

The standard Ebbers fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Ebbers project needs.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Fire-Rated Drywall Ebbers Edmonton | Type X Board

Fire-rated drywall in Ebbers, installed to code

Most fire-rated work we do in Ebbers is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Garage ceilings and garage-to-house separations in Ebbers
Basement legal-suite fire separations
Joints taped as part of the rated assembly, not just for looks
Finished clean and inspection-ready
Type X board to the assembly on the drawings
Rated assemblies installed and sealed correctly
Furnace and mechanical room enclosures

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Ebbers drawings and tell you if what is on site does not match it.

Ebbers drywall in context

About Ebbers

This non-residential neighbourhood is largely commercial or industrial in nature.

What we see in Ebbers

In Ebbers the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Finishing a rated wall in Ebbers without compromising it

Rated first, pretty second

Taping on a rated assembly in Ebbers does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Ebbers are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Why Ebbers homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Ebbers we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Ebbers and Northeast, 7 days a week. Fixed pricing on free Ebbers quotes, a clean site and a guarantee on the work. When an Ebbers job is not right, we make it right — on us.

One-hour and two-hour assemblies

What the number means

A rating is how long a tested assembly resisted fire under laboratory conditions, not a guarantee about your Ebbers house. One hour is the common residential separation; two hour appears between units in some buildings.

Why it changes the build

A two-hour assembly is usually two layers of board with offset joints, which changes material, labour and thickness. It is specified on the drawings and it is not something to substitute down.

What happens when an assembly is altered later

Every future trade is a risk

A rated Ebbers wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Ebbers Edmonton

Free quote

We come out to your Ebbers Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Ebbers Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Ebbers Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Ebbers Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Ebbers Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Ebbers Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Ebbers Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Ebbers Edmonton

Fire-Rated Drywall Ebbers Edmonton: your questions answered

Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
Can you finish the fire-rated board too?: Yes — your Ebbers separation passes code and looks properly finished, ready for paint.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
How do I know which rated assembly my Ebbers project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Where is fire-rated drywall required?: The standard Ebbers fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Ebbers project needs.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Ebbers Edmonton

Fire-rated drywall in Ebbers, installed to code