Where is fire-rated drywall required?

The standard Dunluce fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Dunluce project needs.

Do you stand behind your fire-rated work in Dunluce?

Yes. We install to code and walk the Dunluce job with you, and if something is not right we come back and make it right.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Dunluce garage ceiling and a living room do not need the same finish level.

My Dunluce garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Fire-Rated Drywall Dunluce Edmonton | Type X Board

Fire-rated drywall in Dunluce, installed to code

Where code requires it in Dunluce, fire-rated board is mandatory: garage-to-house separations, suites and party walls take Type X in a rated assembly — for inspection and for safety. In Dunluce we install fire-rated drywall to code and finish it clean. Dunluce is an Northwest community with a mix of older homes and newer builds, so fire-rated work here is common on garages and suites. We cover Dunluce, Albany, Athlone, Baranow and Northwest, 7 days a week.

Basement legal-suite fire separations
Party walls between units
Type X fire-rated board to code in Dunluce
Joints taped as part of the rated assembly, not just for looks
Dunluce coverage — we come to you
Garage ceilings and garage-to-house separations in Dunluce
Type X board to the assembly on the drawings

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Dunluce build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Dunluce drywall in context

About Dunluce

Dunluce is named after a historical castle on the north coast of Ireland.

What we see in Dunluce

In Dunluce the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Dunluce assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Fire-rated garages, suites and party walls in Dunluce

Garage firewalls

The most common fire-rated job in Dunluce is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Dunluce homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Dunluce wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Dunluce. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Dunluce depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Dunluce Edmonton

Free quote

We come out to your Dunluce Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Dunluce Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Dunluce Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Dunluce Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Dunluce Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Dunluce Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Dunluce Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Dunluce Edmonton

Fire-Rated Drywall Dunluce Edmonton: your questions answered

Where is fire-rated drywall required?: The standard Dunluce fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Dunluce project needs.
Do you stand behind your fire-rated work in Dunluce?: Yes. We install to code and walk the Dunluce job with you, and if something is not right we come back and make it right.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Dunluce garage ceiling and a living room do not need the same finish level.
My Dunluce garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Dunluce Edmonton

Fire-rated drywall in Dunluce, installed to code