Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Delton garages where storage access was cut in afterwards and never addressed.

Will it pass inspection in Delton?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Delton separation passes inspection.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Where is fire-rated drywall required?

The standard Delton fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Delton project needs.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Delton ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Fire-Rated Drywall Delton Edmonton | Type X Board

Rated separations in Delton that pass inspection the first time

No shortcuts on Delton fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Delton we install fire-rated drywall to code and finish it clean. Delton is an established south Edmonton community of 1960s-70s homes where ceiling stipple, settling cracks and dated texture are common, so fire-rated work here is common on garages and suites. We cover Delton, Abbottsfield, Alberta Avenue, Beacon Heights and North Central, 7 days a week.

Finished clean and inspection-ready
Party walls between units
Type X fire-rated board to code in Delton
Penetrations firestopped before the finish goes on
Party walls and legal-suite separations
Garage-to-house firewall separations
Joints taped as part of the rated assembly, not just for looks

Why Delton homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Delton we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Delton and North Central, 7 days a week. Fixed pricing on free Delton quotes, a clean site and a guarantee on the work. When an Delton job is not right, we make it right — on us.

Delton drywall in context

About Delton

Delton has been part of Edmonton since 1910, a time when land speculators fuelled a tremendous expansion in the supply of vacant subdivisions.

What we see in Delton

In Delton the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Finishing a rated wall in Delton without compromising it

Rated first, pretty second

Taping on a rated assembly in Delton does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Delton assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Delton are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

What makes drywall fire-rated in Delton

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Delton we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Delton drawings and tell you if what is on site does not match it.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Delton Edmonton

Free quote

We come out to your Delton Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Delton Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Delton Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Delton Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Delton Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Delton Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Delton Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Delton Edmonton

Fire-Rated Drywall Delton Edmonton: your questions answered

Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Delton garages where storage access was cut in afterwards and never addressed.
Will it pass inspection in Delton?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Delton separation passes inspection.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Where is fire-rated drywall required?: The standard Delton fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Delton project needs.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Delton ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Delton Edmonton

Rated separations in Delton that pass inspection the first time