Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Do you install fire-rated drywall in CPR Irvine?

Yes — fire-rated drywall in CPR Irvine is part of our regular work, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.

Where is fire-rated drywall required?

The standard CPR Irvine fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your CPR Irvine project needs.

Can you finish the fire-rated board too?

Yes — your CPR Irvine separation passes code and looks properly finished, ready for paint.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in CPR Irvine garages where storage access was cut in afterwards and never addressed.

Fire-Rated Drywall CPR Irvine Edmonton | Type X Board

Rated separations in CPR Irvine that pass inspection the first time

Most fire-rated work we do in CPR Irvine is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Joints taped as part of the rated assembly, not just for looks
Basement legal-suite fire separations
Rated assemblies installed and sealed correctly
Type X board to the assembly on the drawings
Type X fire-rated board to code in CPR Irvine
Garage-to-house firewall separations
Garage ceilings and garage-to-house separations in CPR Irvine

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated CPR Irvine assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

CPR Irvine drywall in context

About CPR Irvine

This non-residential neighbourhood is largely commercial or industrial in nature.

What we see in CPR Irvine

In CPR Irvine the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Fire-rated garages, suites and party walls in CPR Irvine

Garage firewalls

The most common fire-rated job in CPR Irvine is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in CPR Irvine homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated CPR Irvine assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in CPR Irvine are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Rated does not mean soundproof

Two different goals

People often assume a fire-rated CPR Irvine wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

What happens when an assembly is altered later

Every future trade is a risk

A rated CPR Irvine wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Cpr Irvine Edmonton

Free quote

We come out to your Cpr Irvine Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Cpr Irvine Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Cpr Irvine Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Cpr Irvine Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Cpr Irvine Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Cpr Irvine Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Cpr Irvine Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall CPR Irvine Edmonton

Fire-Rated Drywall CPR Irvine Edmonton: your questions answered

Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Do you install fire-rated drywall in CPR Irvine?: Yes — fire-rated drywall in CPR Irvine is part of our regular work, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.
Where is fire-rated drywall required?: The standard CPR Irvine fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your CPR Irvine project needs.
Can you finish the fire-rated board too?: Yes — your CPR Irvine separation passes code and looks properly finished, ready for paint.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in CPR Irvine garages where storage access was cut in afterwards and never addressed.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall CPR Irvine Edmonton

Rated separations in CPR Irvine that pass inspection the first time