Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

How do I know which rated assembly my Bulyea Heights project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

My Bulyea Heights garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Bulyea Heights garage ceiling and a living room do not need the same finish level.

Do you stand behind your fire-rated work in Bulyea Heights?

Yes. We install to code and walk the Bulyea Heights job with you, and if something is not right we come back and make it right.

Fire-Rated Drywall Bulyea Heights Edmonton | Type X Board

Rated separations in Bulyea Heights that pass inspection the first time

A fire-rated wall is not a board, it is an assembly. In Bulyea Heights that means the specified board thickness and type, the specified stud and screw spacing, taped joints, and every penetration firestopped. Miss any one of those and the rating is not there, whatever the board says on the back.

Type X board to the assembly on the drawings
Party walls between units
Penetrations firestopped before the finish goes on
Garage ceilings and garage-to-house separations in Bulyea Heights
Furnace and mechanical room enclosures
Joints taped as part of the rated assembly, not just for looks
Basement legal-suite fire separations

Fire-rated garages, suites and party walls in Bulyea Heights

Garage firewalls

The most common fire-rated job in Bulyea Heights is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Bulyea Heights homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Bulyea Heights drywall in context

About Bulyea Heights

Bulyea Heights was named after George Hedley Vicars Bulyea (1859-1928), the first Lieutenant-Governor of Alberta.

What we see in Bulyea Heights

In Bulyea Heights the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Bulyea Heights build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Bulyea Heights are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Bulyea Heights assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Why Bulyea Heights homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Bulyea Heights we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Bulyea Heights and Whitemud, 7 days a week. Fixed pricing on free Bulyea Heights quotes, a clean site and a guarantee on the work. When an Bulyea Heights job is not right, we make it right — on us.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Bulyea Heights garages where storage access was cut in afterwards and never addressed.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Bulyea Heights Edmonton

Free quote

We come out to your Bulyea Heights Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Bulyea Heights Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Bulyea Heights Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Bulyea Heights Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Bulyea Heights Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Bulyea Heights Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Bulyea Heights Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Bulyea Heights Edmonton

Fire-Rated Drywall Bulyea Heights Edmonton: your questions answered

Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
How do I know which rated assembly my Bulyea Heights project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
My Bulyea Heights garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Bulyea Heights garage ceiling and a living room do not need the same finish level.
Do you stand behind your fire-rated work in Bulyea Heights?: Yes. We install to code and walk the Bulyea Heights job with you, and if something is not right we come back and make it right.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Bulyea Heights Edmonton

Rated separations in Bulyea Heights that pass inspection the first time