Do you install fire-rated drywall in Bergman?

Yes — fire-rated drywall in Bergman is part of our regular work, and we are usually booked within the week. We also cover Abbottsfield, Alberta Avenue, Beacon Heights and North Central.

Can you finish the fire-rated board too?

Yes — your Bergman separation passes code and looks properly finished, ready for paint.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

How do I know which rated assembly my Bergman project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Bergman ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Will it pass inspection in Bergman?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Bergman separation passes inspection.

Fire-Rated Drywall Bergman Edmonton | Type X Board

Rated separations in Bergman that pass inspection the first time

No shortcuts on Bergman fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Bergman we install fire-rated drywall to code and finish it clean. Bergman is one of North Central's newer communities, where fresh installation and first-year settling work are common, so fire-rated work here is common on garages and suites. We cover Bergman, Abbottsfield, Alberta Avenue, Beacon Heights and North Central, 7 days a week.

Bergman coverage — we come to you
Finished clean and inspection-ready
Type X board to the assembly on the drawings
Garage-to-house firewall separations
Penetrations firestopped before the finish goes on
Basement legal-suite fire separations
Party walls and legal-suite separations

What makes drywall fire-rated in Bergman

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Bergman we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

Bergman drywall in context

About Bergman

Bergman was one neighbourhood that made up the area called Beverly.

What we see in Bergman

In Bergman the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Finishing a rated wall in Bergman without compromising it

Rated first, pretty second

Taping on a rated assembly in Bergman does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Why Bergman homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Bergman we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Bergman and North Central, 7 days a week. Fixed pricing on free Bergman quotes, a clean site and a guarantee on the work. When an Bergman job is not right, we make it right — on us.

Common fire-rated situations in Bergman

In Bergman, bergman sits in Edmonton's North Central district. Bergman was one neighbourhood that made up the area called Beverly. Across roughly 580 homes here, the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We cover Bergman and the surrounding North Central district, 7 days a week. Free on-site quote, one fixed price, and work that holds up after.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Bergman build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Bergman assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Bergman Edmonton

Free quote

We come out to your Bergman Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Bergman Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Bergman Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Bergman Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Bergman Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Bergman Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Bergman Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Bergman Edmonton

Fire-Rated Drywall Bergman Edmonton: your questions answered

Do you install fire-rated drywall in Bergman?: Yes — fire-rated drywall in Bergman is part of our regular work, and we are usually booked within the week. We also cover Abbottsfield, Alberta Avenue, Beacon Heights and North Central.
Can you finish the fire-rated board too?: Yes — your Bergman separation passes code and looks properly finished, ready for paint.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
How do I know which rated assembly my Bergman project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Bergman ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
Will it pass inspection in Bergman?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Bergman separation passes inspection.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Bergman Edmonton

Rated separations in Bergman that pass inspection the first time