Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Bannerman garage ceiling and a living room do not need the same finish level.

How do I know which rated assembly my Bannerman project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Is a fire-rated wall also soundproof?

It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Bannerman ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Can you finish the fire-rated board too?

Yes — your Bannerman separation passes code and looks properly finished, ready for paint.

Fire-Rated Drywall Bannerman Edmonton | Type X Board

Type X board in Bannerman for garages, suites and mechanical rooms

Most fire-rated work we do in Bannerman is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Party walls and legal-suite separations
Type X fire-rated board to code in Bannerman
Furnace and mechanical room enclosures
Joints taped as part of the rated assembly, not just for looks
Finished clean and inspection-ready
Type X board to the assembly on the drawings
Party walls between units

Our Bannerman fire-rated drywall process, step by step

Right board, right build-up

In Bannerman we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Bannerman separation the inspector approves and the eye approves too.

Bannerman drywall in context

About Bannerman

Bannerman, who settled in the Belmont area in 1883, this area is part of the Clareview district and was annexed to the City, along with much of northeast Edmonton, in the early 1960s.

What we see in Bannerman

In Bannerman the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Common fire-rated situations in Bannerman

In Bannerman, bannerman sits in Edmonton's Northeast district. Named for H. Bannerman, who settled in the Belmont area in 1883, this area is part of the Clareview district and was annexed to the City, along with much of northeast Edmonton, in the early 1960s. Across roughly 1,110 homes here, the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We cover Bannerman and the surrounding Northeast district, 7 days a week. We handle all of it the same careful way — on-site quote, fixed price, done right.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Bannerman assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Bannerman. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Bannerman assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

One-hour and two-hour assemblies

What the number means

A rating is how long a tested assembly resisted fire under laboratory conditions, not a guarantee about your Bannerman house. One hour is the common residential separation; two hour appears between units in some buildings.

Why it changes the build

A two-hour assembly is usually two layers of board with offset joints, which changes material, labour and thickness. It is specified on the drawings and it is not something to substitute down.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Bannerman Edmonton

Free quote

We come out to your Bannerman Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Bannerman Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Bannerman Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Bannerman Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Bannerman Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Bannerman Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Bannerman Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Bannerman Edmonton

Fire-Rated Drywall Bannerman Edmonton: your questions answered

Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Bannerman garage ceiling and a living room do not need the same finish level.
How do I know which rated assembly my Bannerman project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Is a fire-rated wall also soundproof?: It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Bannerman ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Can you finish the fire-rated board too?: Yes — your Bannerman separation passes code and looks properly finished, ready for paint.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Bannerman Edmonton

Type X board in Bannerman for garages, suites and mechanical rooms