Is a fire-rated wall also soundproof?

It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Where is fire-rated drywall required?

The standard Allendale fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Allendale project needs.

Fire-Rated Drywall Allendale Edmonton | Type X Board

Rated separations in Allendale that pass inspection the first time

In Allendale the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Allendale we install fire-rated drywall to code and finish it clean. Allendale is an Scona community with a mix of older homes and newer builds, so fire-rated work here is common on garages and suites. We cover Allendale, Argyll, Belgravia, CPR Irvine and Scona, 7 days a week.

Type X board to the assembly on the drawings
Rated assemblies installed and sealed correctly
Allendale coverage — we come to you
Party walls and legal-suite separations
Garage-to-house firewall separations
Type X fire-rated board to code in Allendale
Joints taped as part of the rated assembly, not just for looks

Where Allendale homes usually need rated board

The four common places

Most rated drywall in Allendale houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Allendale project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Allendale drywall in context

About Allendale

Once farmed by the Allen family, this area was annexed by the City of Strathcona in 1907 and became part of Edmonton in 1912 when Strathcona and Edmonton amalgamated.

What we see in Allendale

In Allendale the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Allendale build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Allendale wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Allendale assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

One-hour and two-hour assemblies

What the number means

A rating is how long a tested assembly resisted fire under laboratory conditions, not a guarantee about your Allendale house. One hour is the common residential separation; two hour appears between units in some buildings.

Why it changes the build

A two-hour assembly is usually two layers of board with offset joints, which changes material, labour and thickness. It is specified on the drawings and it is not something to substitute down.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Allendale drawings and tell you if what is on site does not match it.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Allendale Edmonton

Free quote

We come out to your Allendale Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Allendale Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Allendale Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Allendale Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Allendale Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Allendale Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Allendale Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Allendale Edmonton

Fire-Rated Drywall Allendale Edmonton: your questions answered

Is a fire-rated wall also soundproof?: It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Where is fire-rated drywall required?: The standard Allendale fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Allendale project needs.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Allendale Edmonton

Rated separations in Allendale that pass inspection the first time