Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Allard ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

My Allard garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Can you finish the fire-rated board too?

Yes — your Allard separation passes code and looks properly finished, ready for paint.

Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Is a fire-rated wall also soundproof?

It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.

Will it pass inspection in Allard?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Allard separation passes inspection.

Fire-Rated Drywall Allard Edmonton | Type X Board

Rated separations in Allard that pass inspection the first time

Where code requires it in Allard, fire-rated board is mandatory: garage-to-house separations, suites and party walls take Type X in a rated assembly — for inspection and for safety. In Allard we install fire-rated drywall to code and finish it clean. Allard is an Southwest community with a mix of older homes and newer builds, so fire-rated work here is common on garages and suites. We cover Allard, Ambleside, Blackburne, Blackmud Creek and Southwest, 7 days a week.

Type X board to the assembly on the drawings
Basement legal-suite fire separations
Type X fire-rated board to code in Allard
Rated assemblies installed and sealed correctly
Party walls between units
Penetrations firestopped before the finish goes on
Garage ceilings and garage-to-house separations in Allard

What happens when an assembly is altered later

Every future trade is a risk

A rated Allard wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Allard drawings and tell you if what is on site does not match it.

One-hour and two-hour assemblies

What the number means

A rating is how long a tested assembly resisted fire under laboratory conditions, not a guarantee about your Allard house. One hour is the common residential separation; two hour appears between units in some buildings.

Why it changes the build

A two-hour assembly is usually two layers of board with offset joints, which changes material, labour and thickness. It is specified on the drawings and it is not something to substitute down.

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Allard wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

What affects the cost of fire-rated drywall in Allard?

Area and assembly

The cost in Allard depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Allard rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Allard

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Allard project passes the first time.

Fire-rated garages, suites and party walls in Allard

Garage firewalls

The most common fire-rated job in Allard is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Allard homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Allard Edmonton

Free quote

We come out to your Allard Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Allard Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Allard Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Allard Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Allard Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Allard Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Allard Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Allard Edmonton

Fire-Rated Drywall Allard Edmonton: your questions answered

Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Allard ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
My Allard garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Can you finish the fire-rated board too?: Yes — your Allard separation passes code and looks properly finished, ready for paint.
Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.
Is a fire-rated wall also soundproof?: It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.
Will it pass inspection in Allard?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Allard separation passes inspection.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Allard Edmonton

Rated separations in Allard that pass inspection the first time