Do you stand behind your installation work in University of Alberta?

Yes. Before leaving University of Alberta, we walk the boarding together and fix anything not right.

How long does drywall installation take in an University of Alberta home?

Timeline depends on scope. We give you a specific timeline at the on-site quote. Most single-room or single-area jobs in University of Alberta are complete in one to two days. Larger basement or whole-home jobs take longer and are scoped precisely before we start.

What board do you use on University of Alberta exterior basement walls?

Moisture-resistant board on all University of Alberta exterior foundation walls and around plumbing and laundry. Standard 1/2-inch board for interior walls away from moisture in your University of Alberta home.

Do you board for legal suites in Edmonton?

Yes, and we know the spec. A legal secondary suite in Edmonton requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, STC soundproof board on party walls, and moisture-resistant in all wet areas. We board to that spec so the suite passes inspection.

Can the taping crew start right after you board an University of Alberta home?

Yes — we hang board with seams on framing, correct screw pattern and plumb walls, so a taper (or we ourselves) can start the very next day in University of Alberta.

Does it matter which way the board runs?

Yes. Running horizontally puts one long joint at a comfortable working height instead of several vertical ones and usually means fewer joints. Joint placement decides how much finishing the room needs.

Drywall Installation University of Alberta Edmonton | Board & Tape

Drywall installation hung straight and screwed off right

A good University of Alberta finish starts with good boarding. In University of Alberta the board goes up level, correctly screwed, seams on framing, clean cuts at mechanical and corners. University of Alberta is one of Scona’s newest communities — most homes have framed, unfinished basements ready for boarding. We cover University of Alberta, Ambleton, Allendale, Argyll, Belgravia and the surrounding area, 7 days a week.

Drywall boarding and hanging in University of Alberta — new builds and renovations
Ceiling-then-walls basement boarding across University of Alberta
Fire-rated plus soundproof board on University of Alberta suite separations
Basement boarding — ceiling first, walls second
University of Alberta board hung on the correct screw pattern, seams on framing
Moisture-resistant board on University of Alberta exterior walls and wet areas
Fire-rated and soundproof board for University of Alberta legal-suite separations

Our drywall installation process in University of Alberta in Edmonton, step by step

Ceiling board first — always — in University of Alberta homes

Every boarding job in University of Alberta starts with the ceiling. In University of Alberta we board ceilings first — the wall board tucks under and helps carry the ceiling. Skip the University of Alberta order and the ceiling joints go unsupported and crack. In University of Alberta, walls wait until the ceiling is boarded. It is a small thing that makes a significant difference in long-term performance.

Wall boarding, screw pattern and joint placement in University of Alberta

Wall board goes up with the correct screw pattern — every 12 inches on the field, every 8 inches at the perimeter. In University of Alberta, every seam lands on framing, never mid-bay. In University of Alberta, every inside and outside corner is square and clean. In University of Alberta, board stops clean at window and door frames. When the boarding is done in an University of Alberta home, every surface is at the right plane and the taping crew can go straight to work.

University of Alberta drywall in context

About University of Alberta

This multi-use neighbourhood is both residential and educational in nature.

What we see in University of Alberta

In University of Alberta the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Why Edmonton homeowners trust Emplastrum for drywall installation in Edmonton

We board the way a finishing specialist wants it boarded

Most boarding crews treat installation as a volume game — get the board up, move on. Every taping problem we have fixed over the years started with a boarding problem underneath it. We board every Edmonton job the way we would want it boarded before we tape it: ceiling first, correct screw pattern, seams on framing, board plumb. The finish is better because the boarding behind it is right.

Fixed price, same-day reply, all Edmonton quadrants

We cover all four Edmonton quadrants, Edmonton, Allendale, Argyll, Belgravia and Edmonton, 7 days a week — every established and newer Edmonton community from Allendale, Argyll, Belgravia to Allendale, Argyll, Belgravia. Free on-site quotes, fixed prices — you know the number before we start and it does not change.

Our Edmonton drywall installation process in Edmonton, step by step

Ceiling board first — always

Every boarding job in Edmonton starts with the ceiling. Ceiling board goes up before the walls because the wall board butts up under the ceiling board and helps carry it. Reversing the sequence leaves ceiling joints carrying their own weight unsupported — they perform worse under the tape and are more likely to crack over time. No University of Alberta wall board goes up before the ceiling is complete.

Wall boarding — screw pattern, joint placement and board selection

Wall board goes up with the correct screw pattern: every 12 inches on the field, every 8 inches at the perimeter. All seams land on framing. Clean, square corners — inside and out — on University of Alberta jobs. We hold University of Alberta board to the window and door frames, no overrun. When the boarding is complete, every surface is at the right plane, the taping crew can start immediately and there is no rework to do before they begin.

Gapping at the floor and around openings

Board should not touch

A small gap at the slab or subfloor keeps board from wicking moisture and gives the building room to move.

Around windows and doors

Joints are kept away from the corners of openings, because a joint that lines up with a corner is exactly where an University of Alberta house concentrates movement and where cracks appear first. It costs an offcut and saves a callback.

Handling the sheets without damaging them

Damage happens before it goes up

Board stored on edge, dragged, or left where it can take moisture arrives at the wall already compromised, and a crushed edge or a damp corner never finishes well.

On our sites

Stacked flat and dry, carried rather than dragged, and damaged sheets set aside for offcuts rather than hung in an University of Alberta room where they will show through the finish.

What affects the cost of drywall installation in Edmonton in Edmonton?

Square footage, board type and ceiling complexity

The cost of drywall installation in Edmonton comes down to four things: total square footage of wall and ceiling, board type (standard, moisture-resistant, fire-rated and soundproof are priced differently), ceiling complexity (flat ceilings vs. vaulted, cathedral, bulkheads and soffits), and whether the job is a new development or a renovation around existing trades and fixtures. We measure on site and give you a fixed price before we start.

Board spec in Edmonton — right product on every surface

Exterior foundation walls need moisture-resistant board. Moisture-resistant board on all University of Alberta bathroom and laundry walls. Legal suite ceilings need 5/8” Type X fire-rated board. Party walls between a suite and the main living area need STC soundproof board. In University of Alberta, moisture-free interior walls use standard 1/2” board. We map every surface at the on-site quote and specify the right product — so there are no surprises when the inspector comes.

How it works

Simple, clean, on schedule — Drywall Installation in University Of Alberta Edmonton

Free quote

We come out to your University Of Alberta Edmonton property, take a real look at the drywall installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall installation quote in University Of Alberta Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall installation in University Of Alberta Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your University Of Alberta Edmonton home while we finish the drywall installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall installation with us and you're happy with the result in University Of Alberta Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall installation contractor University Of Alberta Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall installation project in University Of Alberta Edmonton.

Read our reviews on Google

FAQ — Drywall Installation University of Alberta Edmonton

Drywall Installation University of Alberta Edmonton: your questions answered

Do you stand behind your installation work in University of Alberta?: Yes. Before leaving University of Alberta, we walk the boarding together and fix anything not right.
How long does drywall installation take in an University of Alberta home in Edmonton?: Timeline depends on scope. We give you a specific timeline at the on-site quote. Most single-room or single-area jobs in University of Alberta are complete in one to two days. Larger basement or whole-home jobs take longer and are scoped precisely before we start.
What board do you use on University of Alberta exterior basement walls?: Moisture-resistant board on all University of Alberta exterior foundation walls and around plumbing and laundry. Standard 1/2-inch board for interior walls away from moisture in your University of Alberta home.
Do you board for legal suites in Edmonton?: Yes, and we know the spec. A legal secondary suite in Edmonton requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, STC soundproof board on party walls, and moisture-resistant in all wet areas. We board to that spec so the suite passes inspection.
Can the taping crew start right after you board an University of Alberta home?: Yes — we hang board with seams on framing, correct screw pattern and plumb walls, so a taper (or we ourselves) can start the very next day in University of Alberta.
Does it matter which way the board runs?: Yes. Running horizontally puts one long joint at a comfortable working height instead of several vertical ones and usually means fewer joints. Joint placement decides how much finishing the room needs.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Drywall Installation University of Alberta Edmonton

Drywall installation hung straight and screwed off right