Do you hang the ceiling board before the walls?

Yes, always. Ceiling board goes up first on every Edmonton installation job. Wall board butts up under the ceiling board and helps carry it. Reversing the sequence leaves ceiling joints unsupported — they crack sooner and perform worse under tape.

Do you do drywall installation in Strathcona?

Yes — Strathcona is part of our regular service area, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.

Why does the ceiling get boarded first?

So the wall sheets push up underneath and support the ceiling edges. The other way leaves the ceiling perimeter unsupported, which is where cracking starts, and it gives a tighter joint at the wall-ceiling line.

Do you board legal suites to spec?

Yes — 5/8-inch Type X fire-rated board on suite ceilings and soundproof board on party walls, to the City of Edmonton suite spec.

Is drywall installation in Strathcona a fixed price?

Yes. We assess the job on site, confirm the scope and give you a fixed price before we start. The number does not change after we begin.

For Strathcona exterior basement walls, what board do you use?

In Strathcona, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Strathcona home.

Drywall Installation Strathcona Edmonton | Board & Tape

Drywall installation in Strathcona — right board, right spec, ready to tape

In Strathcona, the install sets up the finish. Level hanging, right screws, framed seams and clean mechanical/corner cuts — the Strathcona standard. Strathcona homes from the 2000s and 2010s were built with framed, unfinished basements. Full basement boarding is the most common installation call here. We cover Strathcona, Allendale, Argyll, Belgravia and the surrounding area, 7 days a week.

Ceiling-then-walls basement boarding across Strathcona
Moisture-resistant board for Strathcona exterior and wet-area walls
Fire-rated 5/8” Type X on suite ceilings where required
Left ready for taper — no rework needed
Strathcona board hung on the correct screw pattern, seams on framing
Renovation reboarding — removing old board, installing new to current spec
Basement development boarding in Strathcona — ceiling first, then walls

Drywall board types for Edmonton homes

Standard 1/2” drywall — the right choice for most Edmonton walls

Standard 1/2” drywall is correct for interior walls and ceilings in Edmonton homes away from moisture exposure. It is the most common board we install and finishes the same as the rest of the house. Most interior walls and ceilings in Edmonton homes use standard board.

Moisture-resistant, fire-rated and soundproof — where the spec matters

Exterior basement walls need moisture-resistant board even with a vapour barrier. Bathroom and laundry walls need moisture-resistant. Legal suite ceilings require 5/8” Type X fire-rated. STC soundproof board goes on Strathcona suite party walls. We specify the right product for each surface before we pull the first sheet.

Strathcona drywall in context

About Strathcona

Strathcona was named for Lord Strathcona, Hudson Bay Company Governor (1889-1914) and the man chosen to drive the "last spike" of the CPR transcontinental railway.

What we see in Strathcona

In Strathcona the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Drywall board types for Strathcona homes

Standard board for most walls

Standard 1/2-inch drywall is correct for most interior walls and ceilings in Strathcona away from moisture exposure.

Moisture-resistant, fire-rated and soundproof where the spec matters

Exterior basement walls and wet areas need moisture-resistant board; legal suite ceilings need fire-rated board; party walls need soundproof board. We specify the right product for every Strathcona surface before we pull the first sheet.

Our Drywall Installation process in Strathcona in Edmonton

Assess before we start — always in Strathcona

Every job in Strathcona starts with an on-site assessment. We do not guess at scope, board type or texture match. We confirm what is needed, give you a fixed price and only then start the work.

Left clean and paint-ready in Strathcona

When we leave your Strathcona home, the work is done properly — Level 4 tape on every joint, texture matched, surface sanded flat and ready for the painter. No rework from the painter. No callbacks.

Board layout is decided before the first sheet

Where the joints land

On an Strathcona wall, running board horizontally puts one long joint at a comfortable working height instead of several vertical ones, and it usually means fewer joints overall.

Why it is planned

Joint placement decides how much finishing the room needs and where the visible risk sits. Sheets hung wherever they happen to reach is the difference between a wall that finishes easily and one that fights you.

What affects the cost of drywall installation in Edmonton in Edmonton?

Square footage, board type and ceiling complexity

The cost of drywall installation in Edmonton comes down to four things: total square footage of wall and ceiling, board type (standard, moisture-resistant, fire-rated and soundproof are priced differently), ceiling complexity (flat ceilings vs. vaulted, cathedral, bulkheads and soffits), and whether the job is a new development or a renovation around existing trades and fixtures. We measure on site and give you a fixed price before we start.

Board spec in Edmonton — right product on every surface

Exterior foundation walls need moisture-resistant board. Moisture-resistant board on all Strathcona bathroom and laundry walls. Legal suite ceilings need 5/8” Type X fire-rated board. Party walls between a suite and the main living area need STC soundproof board. In Strathcona, moisture-free interior walls use standard 1/2” board. We map every surface at the on-site quote and specify the right product — so there are no surprises when the inspector comes.

Types of Drywall Installation work in Strathcona in Edmonton

New installs, renovation work and repair in Strathcona

We handle the full range of drywall installation work in Strathcona — from brand-new basement boarding and taping to single-room renovation patches and targeted repair work. Every job gets the same Level 4 standard and fixed price commitment.

Legal suites and multi-use spaces in Strathcona

Legal suite work in Strathcona requires specific board specs: fire-rated on the suite ceiling, soundproof on party walls, moisture-resistant in wet areas. We confirm the spec before we start and board to it.

How it works

Simple, clean, on schedule — Drywall Installation in Strathcona Edmonton

Free quote

We come out to your Strathcona Edmonton property, take a real look at the drywall installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall installation quote in Strathcona Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall installation in Strathcona Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Strathcona Edmonton home while we finish the drywall installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall installation with us and you're happy with the result in Strathcona Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall installation contractor Strathcona Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall installation project in Strathcona Edmonton.

Read our reviews on Google

FAQ — Drywall Installation Strathcona Edmonton

Drywall Installation Strathcona Edmonton: your questions answered

Do you hang the ceiling board before the walls?: Yes, always. Ceiling board goes up first on every Edmonton installation job. Wall board butts up under the ceiling board and helps carry it. Reversing the sequence leaves ceiling joints unsupported — they crack sooner and perform worse under tape.
Do you do drywall installation in Strathcona in Edmonton?: Yes — Strathcona is part of our regular service area, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.
Why does the ceiling get boarded first?: So the wall sheets push up underneath and support the ceiling edges. The other way leaves the ceiling perimeter unsupported, which is where cracking starts, and it gives a tighter joint at the wall-ceiling line.
Do you board legal suites to spec?: Yes — 5/8-inch Type X fire-rated board on suite ceilings and soundproof board on party walls, to the City of Edmonton suite spec.
Is drywall installation in Strathcona a fixed price in Edmonton?: Yes. We assess the job on site, confirm the scope and give you a fixed price before we start. The number does not change after we begin.
For Strathcona exterior basement walls, what board do you use?: In Strathcona, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Strathcona home.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Drywall Installation Strathcona Edmonton

Drywall installation in Strathcona — right board, right spec, ready to tape