Is drywall installation in Hays Ridge Area a fixed price?

Yes. We assess the job on site, confirm the scope and give you a fixed price before we start. The number does not change after we begin.

Do you board for legal suites in Hays Ridge Area?

Yes, and we know the spec. A legal secondary suite in Hays Ridge Area requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, and STC soundproof board on the party walls. Moisture-resistant in all wet areas. That spec is how Hays Ridge Area suites board and pass inspection.

For Hays Ridge Area exterior basement walls, what board do you use?

In Hays Ridge Area, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Hays Ridge Area home.

How long does drywall installation take in a Edmonton home?

A standard open basement in a Edmonton new build typically takes one to two days to board. A full renovation or larger new build takes longer depending on scope. Honest scheduling in Hays Ridge Area: the quoted timeline is the real one. The taping crew can usually start the next day.

How long does drywall installation take in an Hays Ridge Area home?

Timeline depends on scope. We give you a specific timeline at the on-site quote. Most single-room or single-area jobs in Hays Ridge Area are complete in one to two days. Larger basement or whole-home jobs take longer and are scoped precisely before we start.

Drywall Installation Hays Ridge Area Edmonton | Board & Tape

Drywall installation in Hays Ridge Area — hung straight, screwed off right

In Hays Ridge Area, the install sets up the finish. Level hanging, right screws, framed seams and clean mechanical/corner cuts — the Hays Ridge Area standard. Hays Ridge Area homes from the 2000s and 2010s were built with framed, unfinished basements. Full basement boarding is the most common installation call here. We cover Hays Ridge Area, Allard, Ambleside, Blackburne and the surrounding area, 7 days a week.

Fire-rated plus soundproof board on Hays Ridge Area suite separations
Fire-rated 5/8” Type X on suite ceilings where required
Hays Ridge Area basement development boarded ceiling-first, then walls
Ceiling-first, then-walls basement boarding in Hays Ridge Area
Basement development boarding in Hays Ridge Area — ceiling first, then walls
Correct screw pattern throughout — all seams on framing
Right screw pattern, all seams landed on framing in Hays Ridge Area

Our Drywall Installation process in Hays Ridge Area in Edmonton

Assess before we start — always in Hays Ridge Area

Every job in Hays Ridge Area starts with an on-site assessment. We do not guess at scope, board type or texture match. We confirm what is needed, give you a fixed price and only then start the work.

Left clean and paint-ready in Hays Ridge Area

When we leave your Hays Ridge Area home, the work is done properly — Level 4 tape on every joint, texture matched, surface sanded flat and ready for the painter. No rework from the painter. No callbacks.

Board layout is decided before the first sheet

Where the joints land

On an Hays Ridge Area wall, running board horizontally puts one long joint at a comfortable working height instead of several vertical ones, and it usually means fewer joints overall.

Why it is planned

Joint placement decides how much finishing the room needs and where the visible risk sits. Sheets hung wherever they happen to reach is the difference between a wall that finishes easily and one that fights you.

Types of Drywall Installation work in Hays Ridge Area in Edmonton

New installs, renovation work and repair in Hays Ridge Area

We handle the full range of drywall installation work in Hays Ridge Area — from brand-new basement boarding and taping to single-room renovation patches and targeted repair work. Every job gets the same Level 4 standard and fixed price commitment.

Legal suites and multi-use spaces in Hays Ridge Area

Legal suite work in Hays Ridge Area requires specific board specs: fire-rated on the suite ceiling, soundproof on party walls, moisture-resistant in wet areas. We confirm the spec before we start and board to it.

What affects the cost of drywall installation in Edmonton in Edmonton?

Square footage, board type and ceiling complexity

The cost of drywall installation in Edmonton comes down to four things: total square footage of wall and ceiling, board type (standard, moisture-resistant, fire-rated and soundproof are priced differently), ceiling complexity (flat ceilings vs. vaulted, cathedral, bulkheads and soffits), and whether the job is a new development or a renovation around existing trades and fixtures. We measure on site and give you a fixed price before we start.

Board spec in Edmonton — right product on every surface

Exterior foundation walls need moisture-resistant board. Moisture-resistant board on all Hays Ridge Area bathroom and laundry walls. Legal suite ceilings need 5/8” Type X fire-rated board. Party walls between a suite and the main living area need STC soundproof board. In Hays Ridge Area, moisture-free interior walls use standard 1/2” board. We map every surface at the on-site quote and specify the right product — so there are no surprises when the inspector comes.

Drywall board types for Edmonton homes

Standard 1/2” drywall — the right choice for most Edmonton walls

Standard 1/2” drywall is correct for interior walls and ceilings in Edmonton homes away from moisture exposure. It is the most common board we install and finishes the same as the rest of the house. Most interior walls and ceilings in Edmonton homes use standard board.

Moisture-resistant, fire-rated and soundproof — where the spec matters

Exterior basement walls need moisture-resistant board even with a vapour barrier. Bathroom and laundry walls need moisture-resistant. Legal suite ceilings require 5/8” Type X fire-rated. STC soundproof board goes on Hays Ridge Area suite party walls. We specify the right product for each surface before we pull the first sheet.

Our Edmonton drywall installation process in Edmonton, step by step

Ceiling board first — always

Every boarding job in Edmonton starts with the ceiling. Ceiling board goes up before the walls because the wall board butts up under the ceiling board and helps carry it. Reversing the sequence leaves ceiling joints carrying their own weight unsupported — they perform worse under the tape and are more likely to crack over time. No Hays Ridge Area wall board goes up before the ceiling is complete.

Wall boarding — screw pattern, joint placement and board selection

Wall board goes up with the correct screw pattern: every 12 inches on the field, every 8 inches at the perimeter. All seams land on framing. Clean, square corners — inside and out — on Hays Ridge Area jobs. We hold Hays Ridge Area board to the window and door frames, no overrun. When the boarding is complete, every surface is at the right plane, the taping crew can start immediately and there is no rework to do before they begin.

How it works

Simple, clean, on schedule — Drywall Installation in Hays Ridge Area Edmonton

Free quote

We come out to your Hays Ridge Area Edmonton property, take a real look at the drywall installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall installation quote in Hays Ridge Area Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall installation in Hays Ridge Area Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Hays Ridge Area Edmonton home while we finish the drywall installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall installation with us and you're happy with the result in Hays Ridge Area Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall installation contractor Hays Ridge Area Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall installation project in Hays Ridge Area Edmonton.

Read our reviews on Google

FAQ — Drywall Installation Hays Ridge Area Edmonton

Drywall Installation Hays Ridge Area Edmonton: your questions answered

Is drywall installation in Hays Ridge Area a fixed price in Edmonton?: Yes. We assess the job on site, confirm the scope and give you a fixed price before we start. The number does not change after we begin.
Do you board for legal suites in Hays Ridge Area?: Yes, and we know the spec. A legal secondary suite in Hays Ridge Area requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, and STC soundproof board on the party walls. Moisture-resistant in all wet areas. That spec is how Hays Ridge Area suites board and pass inspection.
For Hays Ridge Area exterior basement walls, what board do you use?: In Hays Ridge Area, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Hays Ridge Area home.
Do you hang the ceiling board before the walls?: Yes, always. Ceiling board goes up first on every Edmonton installation job. Wall board butts up under the ceiling board and helps carry it. Reversing the sequence leaves ceiling joints unsupported — they crack sooner and perform worse under tape.
How long does drywall installation take in a Edmonton home in Edmonton?: A standard open basement in a Edmonton new build typically takes one to two days to board. A full renovation or larger new build takes longer depending on scope. Honest scheduling in Hays Ridge Area: the quoted timeline is the real one. The taping crew can usually start the next day.
How long does drywall installation take in an Hays Ridge Area home in Edmonton?: Timeline depends on scope. We give you a specific timeline at the on-site quote. Most single-room or single-area jobs in Hays Ridge Area are complete in one to two days. Larger basement or whole-home jobs take longer and are scoped precisely before we start.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Drywall Installation Hays Ridge Area Edmonton

Drywall installation in Hays Ridge Area — hung straight, screwed off right