How long does drywall installation take in a Calder home?

A standard basement in a Calder home typically takes one to two days to board. New construction or a big reno in Calder runs a longer schedule. The Calder timeline you get at the quote is realistic, not optimistic. In Calder, finishing usually begins the day after boarding wraps.

Does Calder taping follow straight after boarding?

Yes — we hang board with seams on framing, correct screw pattern and plumb walls, so a taper (or we ourselves) can start the very next day in Calder.

Do you stand behind your installation work in Calder?

Yes. Before leaving Calder, we walk the boarding together and fix anything not right.

Should the board touch the floor?

No. A small gap keeps it from wicking moisture and gives the building room to move. Joints are also kept away from the corners of window and door openings, because that is where movement concentrates.

For Calder exterior basement walls, what board do you use?

In Calder, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Calder home.

Do you board for legal suites in Calder?

Yes, and we know the spec. A legal secondary suite in Calder requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, and STC soundproof board on the party walls. Moisture-resistant in all wet areas. That spec is how Calder suites board and pass inspection.

Drywall Installation Calder Edmonton | Board & Tape

Drywall installation in Calder, hung straight and screwed off right

In Calder, the install sets up the finish. Level hanging, right screws, framed seams and clean mechanical/corner cuts — the Calder standard. Calder homes from the 2000s and 2010s were built with framed, unfinished basements. Full basement boarding is the most common installation call here. We cover Calder, Albany, Athlone, Baranow and the surrounding area, 7 days a week.

Drywall boarding and hanging in Calder — new builds and renovations
Ceiling-then-walls basement boarding across Calder
Calder legal-suite separations get fire-rated and soundproof board
Basement development boarding in Calder — ceiling first, then walls
Ready for taping when we leave an Calder job — no rework
Drywall boarding and hanging — new builds and renovations
Correct screw pattern and every seam on framing in Calder

Handling the sheets without damaging them

Damage happens before it goes up

Board stored on edge, dragged, or left where it can take moisture arrives at the wall already compromised, and a crushed edge or a damp corner never finishes well.

On our sites

Stacked flat and dry, carried rather than dragged, and damaged sheets set aside for offcuts rather than hung in an Calder room where they will show through the finish.

Calder drywall in context

About Calder

In the early part of the 20th century, Calder was part of the Hudson's Bay Company Reserve and settled primarily by employees of the Grand Trunk Pacific Railway.

What we see in Calder

In Calder the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

The number we quote is the number you pay

Priced on site, then fixed

An install price that moves halfway through is the most common complaint we hear about the trade. We quote Calder homeowners a fixed price at the on-site quote and the number does not change.

The standard we hang to, across Calder and Albany, Athlone, Baranow

Every joint taped to Level 4, every texture matched precisely, and the walls left paint-ready rather than left for the painter to make good. Free on-site quotes, same-day reply, 7 days a week, throughout Calder, Albany, Athlone, Baranow and surrounding communities. Call or text ' . emp_phone() . '.

Drywall board types for Edmonton homes

Standard 1/2” drywall — the right choice for most Edmonton walls

Standard 1/2” drywall is correct for interior walls and ceilings in Edmonton homes away from moisture exposure. It is the most common board we install and finishes the same as the rest of the house. Most interior walls and ceilings in Edmonton homes use standard board.

Moisture-resistant, fire-rated and soundproof — where the spec matters

Exterior basement walls need moisture-resistant board even with a vapour barrier. Bathroom and laundry walls need moisture-resistant. Legal suite ceilings require 5/8” Type X fire-rated. STC soundproof board goes on Calder suite party walls. We specify the right product for each surface before we pull the first sheet.

Board layout is decided before the first sheet

Where the joints land

On an Calder wall, running board horizontally puts one long joint at a comfortable working height instead of several vertical ones, and it usually means fewer joints overall.

Why it is planned

Joint placement decides how much finishing the room needs and where the visible risk sits. Sheets hung wherever they happen to reach is the difference between a wall that finishes easily and one that fights you.

Why Edmonton homeowners trust Emplastrum for drywall installation in Edmonton

We board the way a finishing specialist wants it boarded

Most boarding crews treat installation as a volume game — get the board up, move on. Every taping problem we have fixed over the years started with a boarding problem underneath it. We board every Edmonton job the way we would want it boarded before we tape it: ceiling first, correct screw pattern, seams on framing, board plumb. The finish is better because the boarding behind it is right.

Fixed price, same-day reply, all Edmonton quadrants

We cover all four Edmonton quadrants, Edmonton, Albany, Athlone, Baranow and Edmonton, 7 days a week — every established and newer Edmonton community from Albany, Athlone, Baranow to Albany, Athlone, Baranow. Free on-site quotes, fixed prices — you know the number before we start and it does not change.

About Drywall Installation in Calder in Edmonton

Drywall Installation in Calder — what to expect

We provide drywall installation services in Calder and surrounding communities, 7 days a week. Calder is one of Northwest’s oldest communities, with homes from the 1960s and 1970s. Renovation drywall, stipple and popcorn ceiling removal and crack repair are among the most common drywall calls from this established Northwest area.

Fixed price — assessed on site in Calder

We assess the job on site, confirm the scope and give you a fixed price before we start. The number does not change after we begin unless the scope changes and we agree on it first.

How it works

Simple, clean, on schedule — Drywall Installation in Calder Edmonton

Free quote

We come out to your Calder Edmonton property, take a real look at the drywall installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall installation quote in Calder Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall installation in Calder Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Calder Edmonton home while we finish the drywall installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall installation with us and you're happy with the result in Calder Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall installation contractor Calder Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall installation project in Calder Edmonton.

Read our reviews on Google

FAQ — Drywall Installation Calder Edmonton

Drywall Installation Calder Edmonton: your questions answered

How long does drywall installation take in a Calder home in Edmonton?: A standard basement in a Calder home typically takes one to two days to board. New construction or a big reno in Calder runs a longer schedule. The Calder timeline you get at the quote is realistic, not optimistic. In Calder, finishing usually begins the day after boarding wraps.
Does Calder taping follow straight after boarding?: Yes — we hang board with seams on framing, correct screw pattern and plumb walls, so a taper (or we ourselves) can start the very next day in Calder.
Do you stand behind your installation work in Calder?: Yes. Before leaving Calder, we walk the boarding together and fix anything not right.
Should the board touch the floor?: No. A small gap keeps it from wicking moisture and gives the building room to move. Joints are also kept away from the corners of window and door openings, because that is where movement concentrates.
For Calder exterior basement walls, what board do you use?: In Calder, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Calder home.
Do you board for legal suites in Calder?: Yes, and we know the spec. A legal secondary suite in Calder requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, and STC soundproof board on the party walls. Moisture-resistant in all wet areas. That spec is how Calder suites board and pass inspection.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Drywall Installation Calder Edmonton

Drywall installation in Calder, hung straight and screwed off right