Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Does it matter if the batt is squashed in a bit?

Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Wellington bays and cut to fit rather than forcing a standard batt in.

Will insulating an interior wall help with noise?

Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Can batts go straight against my Wellington basement concrete?

No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.

Faced or unfaced batts?

One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.

Batt Insulation Wellington Edmonton | Wall Batts

Mineral wool and fibreglass batts in Wellington walls and ceilings

Most of what separates good batt work from bad in Wellington is invisible once the drywall is on. That is exactly why it is worth doing carefully: nobody can inspect it later without opening the wall, and the difference shows up as a cold room rather than as a visible defect.

Rim joists insulated and air-sealed
Split and fitted around wiring and electrical boxes
Odd bays cut to fit rather than packed
Batts friction-fit to full cavity width, not compressed
Vapour control detailed before the board goes on
Mineral wool where fire or sound performance matters

Insulating around plumbing on an exterior wall

Pipes belong on the warm side

A water line run in an Wellington exterior wall cavity with the batt behind it is sitting on the cold side of the insulation. In February that is a freeze risk.

What we do

Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays in the heated space. Where it does not, we flag it rather than boarding over a line we know is exposed.

Sound as a side effect of insulating

You get some for free

Filling an interior Wellington wall cavity with batts noticeably reduces voice and television noise between rooms, even when sound was not the reason for the job.

Where to spend a little more

If a bedroom, office or bathroom wall is being opened anyway, upgrading that specific cavity to a denser acoustic or mineral wool batt costs very little on top of work already happening. We will point out which walls those are while we are quoting.

Batts around ducts and services

What is on the cold side

A duct or pipe run through an exterior Wellington bay must have insulation behind it, between it and the outside, not merely stuffed in around it.

Consequence of getting it wrong

A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question. It is worth the extra few minutes on each bay.

Mineral wool against fibreglass in Wellington

Different tools

Fibreglass batts are the common choice and perform well when fitted properly. Mineral wool is denser, holds its shape better in a cavity, handles fire differently and performs noticeably better for sound.

Where we would spend the difference

Party walls, bedrooms, mechanical rooms and any assembly where sound or fire matters. For an ordinary interior partition in Wellington, fibreglass fitted well beats mineral wool fitted badly.

Insulating a Wellington basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Wellington is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Wellington basement smells musty a year later.

Vapour control, and why the order matters

Warm side, always

In Wellington the vapour barrier goes on the warm side of the insulation. Putting it in the wrong place, or having two of them, traps moisture inside the assembly where it cannot dry.

Sequencing

Insulation is completed and inspected before the barrier goes on, and the barrier is sealed at penetrations before boarding. Once drywall is up, none of this can be corrected without taking the wall apart again.

How it works

Simple, clean, on schedule — Batt Insulation in Wellington Edmonton

Free quote

We come out to your Wellington Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Wellington Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Wellington Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Wellington Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Wellington Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Wellington Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Wellington Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Wellington Edmonton

Batt Insulation Wellington Edmonton: your questions answered

Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Does it matter if the batt is squashed in a bit?: Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Wellington bays and cut to fit rather than forcing a standard batt in.
Will insulating an interior wall help with noise?: Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
Can batts go straight against my Wellington basement concrete?: No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.
Faced or unfaced batts?: One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Wellington Edmonton

Mineral wool and fibreglass batts in Wellington walls and ceilings