Why is my Stewart Greens basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Can you fill my vaulted ceiling completely?

No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.

There is a water pipe in my exterior wall. What happens to it?

Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays on the heated side. If it cannot, we flag it rather than boarding over a line we know is exposed to freezing.

Will insulating an interior wall help with noise?

Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.

Do you insulate knee walls and attic hatches?

Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Batt Insulation Stewart Greens Edmonton | Wall Batts

Batt insulation in Stewart Greens, fitted rather than stuffed

A batt only performs if it fills the cavity completely and is not squashed. In Stewart Greens the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Mineral wool where fire or sound performance matters
Rim joists insulated and air-sealed
Odd bays cut to fit rather than packed
Split and fitted around wiring and electrical boxes
Vapour control detailed before the board goes on
Batts friction-fit to full cavity width, not compressed

Cutting to the bay, not the label

Real framing is not nominal

Stewart Greens walls, especially in older homes and renovations, carry bays that are wider or narrower than standard, plus cripples, blocking and services.

What we do

Measure and cut. A batt forced into a narrow bay is compressed and underperforms; one left short in a wide bay leaves a gap that convects. Both are invisible after boarding.

Attic hatches, knee walls and the bits at the edges

Small areas, outsized effect

Knee walls in a Stewart Greens storey-and-a-half, the back of an attic hatch and the ends of joist bays are commonly left bare because they are awkward.

Why we do them anyway

They are direct openings between heated and unheated space. A wall insulated to a high standard with an uninsulated knee wall beside it performs like the weaker of the two, and those edges are where cold rooms usually trace back to.

Friction fit, not stapled tight

How a batt is meant to sit

An unfaced batt holds itself in an Stewart Greens bay by friction across its full width, touching the framing on both sides and the sheathing behind.

The common shortcut

Pulling a faced batt tight and stapling the flanges to the face of the stud, which dishes the middle and leaves a void behind. It looks tidy from the room and performs worse than it measures.

Faced, unfaced, and the vapour question

Two systems

A kraft-faced batt carries its own vapour retarder; unfaced batts are paired with a separate poly barrier over the whole wall.

Why it matters here

Using both in the same Stewart Greens assembly can trap moisture between two retarders. We pick one system for the wall and stay with it rather than mixing what is on the shelf.

Insulating an existing Stewart Greens wall without opening it

The honest limits

Batts need an open cavity. If a Stewart Greens wall is finished and staying finished, batts are not the product — that is a job for a blown-in or injected material, or for adding insulation on the room side.

What we say

We would rather tell you batts are the wrong answer for a closed wall than sell you a partial job. Where the wall is already open for other work, that is the moment to insulate properly.

Sound as a side effect of insulating

You get some for free

Filling an interior Stewart Greens wall cavity with batts noticeably reduces voice and television noise between rooms, even when sound was not the reason for the job.

Where to spend a little more

If a bedroom, office or bathroom wall is being opened anyway, upgrading that specific cavity to a denser acoustic or mineral wool batt costs very little on top of work already happening. We will point out which walls those are while we are quoting.

How it works

Simple, clean, on schedule — Batt Insulation in Stewart Greens Edmonton

Free quote

We come out to your Stewart Greens Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Stewart Greens Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Stewart Greens Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Stewart Greens Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Stewart Greens Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Stewart Greens Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Stewart Greens Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Stewart Greens Edmonton

Batt Insulation Stewart Greens Edmonton: your questions answered

Why is my Stewart Greens basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.
Can you fill my vaulted ceiling completely?: No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.
There is a water pipe in my exterior wall. What happens to it?: Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays on the heated side. If it cannot, we flag it rather than boarding over a line we know is exposed to freezing.
Will insulating an interior wall help with noise?: Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.
Do you insulate knee walls and attic hatches?: Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Stewart Greens Edmonton

Batt insulation in Stewart Greens, fitted rather than stuffed