Can you fill my vaulted ceiling completely?

No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.

Does it matter if the batt is squashed in a bit?

Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Richford bays and cut to fit rather than forcing a standard batt in.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Can the rafter bays be filled right up?

Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.

Can batts go straight against my Richford basement concrete?

No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.

Batt Insulation Richford Edmonton | Wall Batts

Mineral wool and fibreglass batts in Richford walls and ceilings

A batt only performs if it fills the cavity completely and is not squashed. In Richford the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Rim joists insulated and air-sealed
Odd bays cut to fit rather than packed
Vapour control detailed before the board goes on
Batts friction-fit to full cavity width, not compressed
Mineral wool where fire or sound performance matters
Split and fitted around wiring and electrical boxes

Mineral wool against fibreglass in Richford

Different tools

Fibreglass batts are the common choice and perform well when fitted properly. Mineral wool is denser, holds its shape better in a cavity, handles fire differently and performs noticeably better for sound.

Where we would spend the difference

Party walls, bedrooms, mechanical rooms and any assembly where sound or fire matters. For an ordinary interior partition in Richford, fibreglass fitted well beats mineral wool fitted badly.

Vapour control, and why the order matters

Warm side, always

In Richford the vapour barrier goes on the warm side of the insulation. Putting it in the wrong place, or having two of them, traps moisture inside the assembly where it cannot dry.

Sequencing

Insulation is completed and inspected before the barrier goes on, and the barrier is sealed at penetrations before boarding. Once drywall is up, none of this can be corrected without taking the wall apart again.

Garage-to-house walls and ceilings

Two jobs at once

The wall between an Richford garage and the house, and the ceiling under living space, usually need a fire separation as well as insulation. The two have to be planned together because the board and the assembly are specified.

Sequencing

Insulation and vapour control go in, get inspected, then the rated board goes on. Doing it in the wrong order means opening a finished rated assembly, which is the expensive way to discover the sequence.

Friction fit, not stapled tight

How a batt is meant to sit

An unfaced batt holds itself in an Richford bay by friction across its full width, touching the framing on both sides and the sheathing behind.

The common shortcut

Pulling a faced batt tight and stapling the flanges to the face of the stud, which dishes the middle and leaves a void behind. It looks tidy from the room and performs worse than it measures.

Cathedral ceilings and the ventilation gap

Do not fill it to the deck

In a vaulted Richford ceiling there has to be an air channel between the insulation and the roof sheathing. Packing batts tight to the deck closes it, and the roof has no way to dry.

What that costs later

Damp sheathing, mould and in the worst cases rot — none of it visible until it is expensive. The batt is sized so the channel stays open, which means accepting slightly less insulation depth in exchange for a roof that lasts.

Insulating around plumbing on an exterior wall

Pipes belong on the warm side

A water line run in an Richford exterior wall cavity with the batt behind it is sitting on the cold side of the insulation. In February that is a freeze risk.

What we do

Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays in the heated space. Where it does not, we flag it rather than boarding over a line we know is exposed.

How it works

Simple, clean, on schedule — Batt Insulation in Richford Edmonton

Free quote

We come out to your Richford Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Richford Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Richford Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Richford Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Richford Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Richford Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Richford Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Richford Edmonton

Batt Insulation Richford Edmonton: your questions answered

Can you fill my vaulted ceiling completely?: No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.
Does it matter if the batt is squashed in a bit?: Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Richford bays and cut to fit rather than forcing a standard batt in.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Can the rafter bays be filled right up?: Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.
Can batts go straight against my Richford basement concrete?: No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Richford Edmonton

Mineral wool and fibreglass batts in Richford walls and ceilings