Will insulating an interior wall help with noise?

Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Should batts be stapled tight to the studs?

The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.

My room is cold and draughty. Will batts fix it?

Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.

What about the pipes in my exterior wall?

Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Batt Insulation Richfield Edmonton | Wall Batts

Mineral wool and fibreglass batts in Richfield walls and ceilings

A batt only performs if it fills the cavity completely and is not squashed. In Richfield the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Rim joists insulated and air-sealed
Mineral wool where fire or sound performance matters
Batts friction-fit to full cavity width, not compressed
Vapour control detailed before the board goes on
Split and fitted around wiring and electrical boxes
Odd bays cut to fit rather than packed

Batts around ducts and services

What is on the cold side

A duct or pipe run through an exterior Richfield bay must have insulation behind it, between it and the outside, not merely stuffed in around it.

Consequence of getting it wrong

A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question. It is worth the extra few minutes on each bay.

Richfield drywall in context

About Richfield

Part of Mill Woods, Richfield was developed in the 1970s in a system of pleasantly curving streets and cul-de-sacs.

What we see in Richfield

In Richfield the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Compression is the most common Richfield mistake

A squashed batt is a weaker batt

Batt insulation works because of the still air trapped in it. Compress it into a narrower bay and you lose a meaningful share of its performance while paying for the full product.

The fix is measurement

Richfield framing is not always at a standard spacing, especially in older homes and renovations. We measure the bays and cut to fit rather than forcing a standard batt into a non-standard cavity.

Insulating around plumbing on an exterior wall

Pipes belong on the warm side

A water line run in an Richfield exterior wall cavity with the batt behind it is sitting on the cold side of the insulation. In February that is a freeze risk.

What we do

Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays in the heated space. Where it does not, we flag it rather than boarding over a line we know is exposed.

Mineral wool against fibreglass in Richfield

Different tools

Fibreglass batts are the common choice and perform well when fitted properly. Mineral wool is denser, holds its shape better in a cavity, handles fire differently and performs noticeably better for sound.

Where we would spend the difference

Party walls, bedrooms, mechanical rooms and any assembly where sound or fire matters. For an ordinary interior partition in Richfield, fibreglass fitted well beats mineral wool fitted badly.

Cutting to the bay, not the label

Real framing is not nominal

Richfield walls, especially in older homes and renovations, carry bays that are wider or narrower than standard, plus cripples, blocking and services.

What we do

Measure and cut. A batt forced into a narrow bay is compressed and underperforms; one left short in a wide bay leaves a gap that convects. Both are invisible after boarding.

Kneewalls and the rooms in the roof

A cold face nobody sees

A kneewall in an Richfield storey-and-a-half has attic space directly behind it, so the back of that batt is exposed to outdoor air.

What it needs

The batt supported and its back face covered, rather than left open to the attic where air washes straight through it. Uncovered kneewall insulation is one of the most common finds in older homes.

How it works

Simple, clean, on schedule — Batt Insulation in Richfield Edmonton

Free quote

We come out to your Richfield Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Richfield Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Richfield Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Richfield Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Richfield Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Richfield Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Richfield Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Richfield Edmonton

Batt Insulation Richfield Edmonton: your questions answered

Will insulating an interior wall help with noise?: Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
Should batts be stapled tight to the studs?: The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.
My room is cold and draughty. Will batts fix it?: Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.
What about the pipes in my exterior wall?: Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Richfield Edmonton

Mineral wool and fibreglass batts in Richfield walls and ceilings