Do you insulate knee walls and attic hatches?

Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.

There is a water pipe in my exterior wall. What happens to it?

Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays on the heated side. If it cannot, we flag it rather than boarding over a line we know is exposed to freezing.

What about the pipes in my exterior wall?

Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.

Will insulating an interior wall help with noise?

Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Faced or unfaced batts?

One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.

Batt Insulation Parkview Edmonton | Wall Batts

Mineral wool and fibreglass batts in Parkview walls and ceilings

A batt only performs if it fills the cavity completely and is not squashed. In Parkview the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Batts friction-fit to full cavity width, not compressed
Vapour control detailed before the board goes on
Split and fitted around wiring and electrical boxes
Mineral wool where fire or sound performance matters
Rim joists insulated and air-sealed
Odd bays cut to fit rather than packed

Insulating a Parkview basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Parkview is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Parkview basement smells musty a year later.

Parkview drywall in context

About Parkview

One of the City's larger neighbourhoods, dating to the 1950s, Parkview is a beautiful area featuring mature trees, attractively landscaped homes on quiet streets, and breathtaking views of the river valley.

What we see in Parkview

In Parkview the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Vapour control, and why the order matters

Warm side, always

In Parkview the vapour barrier goes on the warm side of the insulation. Putting it in the wrong place, or having two of them, traps moisture inside the assembly where it cannot dry.

Sequencing

Insulation is completed and inspected before the barrier goes on, and the barrier is sealed at penetrations before boarding. Once drywall is up, none of this can be corrected without taking the wall apart again.

Cathedral ceilings and leaving the air gap

Do not fill it completely

A vented cathedral ceiling in an Parkview home needs a clear air channel between the insulation and the roof sheathing.

Why

Packing the rafter bay full removes the ventilation that keeps the deck cold and dry, which is how a warm sloped ceiling ends up with a damp deck. Baffles hold the channel open.

Batts around ducts and services

What is on the cold side

A duct or pipe run through an exterior Parkview bay must have insulation behind it, between it and the outside, not merely stuffed in around it.

Consequence of getting it wrong

A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question. It is worth the extra few minutes on each bay.

Wiring, boxes and the gaps behind them

Where the cold gets in

The fastest way to ruin a wall in Parkview is to stuff the batt behind the wiring and the electrical boxes. It leaves an uninsulated void exactly where there is already a hole in the vapour barrier.

Split, do not stuff

The batt is split so half sits behind the cable and half in front, and it is cut around boxes rather than compressed past them. It is slower and it is the difference between a wall that performs and one that only looks insulated.

Faced, unfaced, and the vapour question

Two systems

A kraft-faced batt carries its own vapour retarder; unfaced batts are paired with a separate poly barrier over the whole wall.

Why it matters here

Using both in the same Parkview assembly can trap moisture between two retarders. We pick one system for the wall and stay with it rather than mixing what is on the shelf.

How it works

Simple, clean, on schedule — Batt Insulation in Parkview Edmonton

Free quote

We come out to your Parkview Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Parkview Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Parkview Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Parkview Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Parkview Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Parkview Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Parkview Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Parkview Edmonton

Batt Insulation Parkview Edmonton: your questions answered

Do you insulate knee walls and attic hatches?: Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.
There is a water pipe in my exterior wall. What happens to it?: Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays on the heated side. If it cannot, we flag it rather than boarding over a line we know is exposed to freezing.
What about the pipes in my exterior wall?: Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.
Will insulating an interior wall help with noise?: Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Faced or unfaced batts?: One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Parkview Edmonton

Mineral wool and fibreglass batts in Parkview walls and ceilings