Does the garage wall need anything special?

Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.

What about the pipes in my exterior wall?

Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Will insulating an interior wall help with noise?

Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Do you cut batts to fit?

Yes. Real Ormsby Place framing carries bays wider or narrower than nominal, plus cripples and blocking. Forced batts are compressed and underperform; short ones leave gaps that convect. Both are invisible after boarding.

Batt Insulation Ormsby Place Edmonton | Wall Batts

Batt insulation in Ormsby Place, fitted rather than stuffed

A batt only performs if it fills the cavity completely and is not squashed. In Ormsby Place the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Vapour control detailed before the board goes on
Mineral wool where fire or sound performance matters
Odd bays cut to fit rather than packed
Batts friction-fit to full cavity width, not compressed
Split and fitted around wiring and electrical boxes
Rim joists insulated and air-sealed

Cutting to the bay, not the label

Real framing is not nominal

Ormsby Place walls, especially in older homes and renovations, carry bays that are wider or narrower than standard, plus cripples, blocking and services.

What we do

Measure and cut. A batt forced into a narrow bay is compressed and underperforms; one left short in a wide bay leaves a gap that convects. Both are invisible after boarding.

Ormsby Place drywall in context

About Ormsby Place

Named for the man responsible for developing Edmonton's grid system of numbering streets and avenues, Ormsby Place is located in the City's west end.

What we see in Ormsby Place

In Ormsby Place the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Garage-to-house walls and ceilings

Two jobs at once

The wall between an Ormsby Place garage and the house, and the ceiling under living space, usually need a fire separation as well as insulation. The two have to be planned together because the board and the assembly are specified.

Sequencing

Insulation and vapour control go in, get inspected, then the rated board goes on. Doing it in the wrong order means opening a finished rated assembly, which is the expensive way to discover the sequence.

Cathedral ceilings and leaving the air gap

Do not fill it completely

A vented cathedral ceiling in an Ormsby Place home needs a clear air channel between the insulation and the roof sheathing.

Why

Packing the rafter bay full removes the ventilation that keeps the deck cold and dry, which is how a warm sloped ceiling ends up with a damp deck. Baffles hold the channel open.

Cathedral ceilings and the ventilation gap

Do not fill it to the deck

In a vaulted Ormsby Place ceiling there has to be an air channel between the insulation and the roof sheathing. Packing batts tight to the deck closes it, and the roof has no way to dry.

What that costs later

Damp sheathing, mould and in the worst cases rot — none of it visible until it is expensive. The batt is sized so the channel stays open, which means accepting slightly less insulation depth in exchange for a roof that lasts.

Insulating a Ormsby Place basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Ormsby Place is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Ormsby Place basement smells musty a year later.

Handling, dust and leaving it clean

Practical realities

Batt work makes airborne fibre and it settles everywhere if the space is not controlled.

How the site is run

Covered openings, the crew in proper protection, offcuts bagged rather than swept into the cavity, and a vacuum through the Ormsby Place space at the end of the day rather than at the end of the job.

How it works

Simple, clean, on schedule — Batt Insulation in Ormsby Place Edmonton

Free quote

We come out to your Ormsby Place Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Ormsby Place Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Ormsby Place Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Ormsby Place Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Ormsby Place Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Ormsby Place Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Ormsby Place Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Ormsby Place Edmonton

Batt Insulation Ormsby Place Edmonton: your questions answered

Does the garage wall need anything special?: Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.
What about the pipes in my exterior wall?: Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Will insulating an interior wall help with noise?: Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
Do you cut batts to fit?: Yes. Real Ormsby Place framing carries bays wider or narrower than nominal, plus cripples and blocking. Forced batts are compressed and underperform; short ones leave gaps that convect. Both are invisible after boarding.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Ormsby Place Edmonton

Batt insulation in Ormsby Place, fitted rather than stuffed