Do you install the vapour barrier as well?

Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

Can you fill my vaulted ceiling completely?

No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.

What about the pipes in my exterior wall?

Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.

My room is cold and draughty. Will batts fix it?

Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.

Does the garage wall need anything special?

Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.

Should batts be stapled tight to the studs?

The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.

Batt Insulation Ogilvie Ridge Edmonton | Wall Batts

Batt insulation in Ogilvie Ridge before the vapour barrier goes on

A batt only performs if it fills the cavity completely and is not squashed. In Ogilvie Ridge the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Batts friction-fit to full cavity width, not compressed
Rim joists insulated and air-sealed
Vapour control detailed before the board goes on
Mineral wool where fire or sound performance matters
Odd bays cut to fit rather than packed
Split and fitted around wiring and electrical boxes

Compression is the most common Ogilvie Ridge mistake

A squashed batt is a weaker batt

Batt insulation works because of the still air trapped in it. Compress it into a narrower bay and you lose a meaningful share of its performance while paying for the full product.

The fix is measurement

Ogilvie Ridge framing is not always at a standard spacing, especially in older homes and renovations. We measure the bays and cut to fit rather than forcing a standard batt into a non-standard cavity.

Cathedral ceilings and the ventilation gap

Do not fill it to the deck

In a vaulted Ogilvie Ridge ceiling there has to be an air channel between the insulation and the roof sheathing. Packing batts tight to the deck closes it, and the roof has no way to dry.

What that costs later

Damp sheathing, mould and in the worst cases rot — none of it visible until it is expensive. The batt is sized so the channel stays open, which means accepting slightly less insulation depth in exchange for a roof that lasts.

Kneewalls and the rooms in the roof

A cold face nobody sees

A kneewall in an Ogilvie Ridge storey-and-a-half has attic space directly behind it, so the back of that batt is exposed to outdoor air.

What it needs

The batt supported and its back face covered, rather than left open to the attic where air washes straight through it. Uncovered kneewall insulation is one of the most common finds in older homes.

Insulating a Ogilvie Ridge basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Ogilvie Ridge is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Ogilvie Ridge basement smells musty a year later.

Attic hatches, knee walls and the bits at the edges

Small areas, outsized effect

Knee walls in a Ogilvie Ridge storey-and-a-half, the back of an attic hatch and the ends of joist bays are commonly left bare because they are awkward.

Why we do them anyway

They are direct openings between heated and unheated space. A wall insulated to a high standard with an uninsulated knee wall beside it performs like the weaker of the two, and those edges are where cold rooms usually trace back to.

Faced, unfaced, and the vapour question

Two systems

A kraft-faced batt carries its own vapour retarder; unfaced batts are paired with a separate poly barrier over the whole wall.

Why it matters here

Using both in the same Ogilvie Ridge assembly can trap moisture between two retarders. We pick one system for the wall and stay with it rather than mixing what is on the shelf.

How it works

Simple, clean, on schedule — Batt Insulation in Ogilvie Ridge Edmonton

Free quote

We come out to your Ogilvie Ridge Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Ogilvie Ridge Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Ogilvie Ridge Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Ogilvie Ridge Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Ogilvie Ridge Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Ogilvie Ridge Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Ogilvie Ridge Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Ogilvie Ridge Edmonton

Batt Insulation Ogilvie Ridge Edmonton: your questions answered

Do you install the vapour barrier as well?: Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.
Can you fill my vaulted ceiling completely?: No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.
What about the pipes in my exterior wall?: Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.
My room is cold and draughty. Will batts fix it?: Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.
Does the garage wall need anything special?: Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.
Should batts be stapled tight to the studs?: The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Ogilvie Ridge Edmonton

Batt insulation in Ogilvie Ridge before the vapour barrier goes on