My room is cold and draughty. Will batts fix it?

Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.

Can the rafter bays be filled right up?

Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.

Will insulating an interior wall help with noise?

Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.

Why is my Klarvatten basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Does the garage wall need anything special?

Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.

What about the wiring in the wall?

The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Batt Insulation Klarvatten Edmonton | Wall Batts

Batt insulation in Klarvatten, fitted rather than stuffed

A batt only performs if it fills the cavity completely and is not squashed. In Klarvatten the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Batts friction-fit to full cavity width, not compressed
Odd bays cut to fit rather than packed
Vapour control detailed before the board goes on
Split and fitted around wiring and electrical boxes
Rim joists insulated and air-sealed
Mineral wool where fire or sound performance matters

Batts around ducts and services

What is on the cold side

A duct or pipe run through an exterior Klarvatten bay must have insulation behind it, between it and the outside, not merely stuffed in around it.

Consequence of getting it wrong

A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question. It is worth the extra few minutes on each bay.

Insulating around plumbing on an exterior wall

Pipes belong on the warm side

A water line run in an Klarvatten exterior wall cavity with the batt behind it is sitting on the cold side of the insulation. In February that is a freeze risk.

What we do

Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays in the heated space. Where it does not, we flag it rather than boarding over a line we know is exposed.

Sound as a side effect of insulating

You get some for free

Filling an interior Klarvatten wall cavity with batts noticeably reduces voice and television noise between rooms, even when sound was not the reason for the job.

Where to spend a little more

If a bedroom, office or bathroom wall is being opened anyway, upgrading that specific cavity to a denser acoustic or mineral wool batt costs very little on top of work already happening. We will point out which walls those are while we are quoting.

Compression is the most common Klarvatten mistake

A squashed batt is a weaker batt

Batt insulation works because of the still air trapped in it. Compress it into a narrower bay and you lose a meaningful share of its performance while paying for the full product.

The fix is measurement

Klarvatten framing is not always at a standard spacing, especially in older homes and renovations. We measure the bays and cut to fit rather than forcing a standard batt into a non-standard cavity.

Vapour control, and why the order matters

Warm side, always

In Klarvatten the vapour barrier goes on the warm side of the insulation. Putting it in the wrong place, or having two of them, traps moisture inside the assembly where it cannot dry.

Sequencing

Insulation is completed and inspected before the barrier goes on, and the barrier is sealed at penetrations before boarding. Once drywall is up, none of this can be corrected without taking the wall apart again.

Handling, dust and leaving it clean

Practical realities

Batt work makes airborne fibre and it settles everywhere if the space is not controlled.

How the site is run

Covered openings, the crew in proper protection, offcuts bagged rather than swept into the cavity, and a vacuum through the Klarvatten space at the end of the day rather than at the end of the job.

How it works

Simple, clean, on schedule — Batt Insulation in Klarvatten Edmonton

Free quote

We come out to your Klarvatten Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Klarvatten Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Klarvatten Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Klarvatten Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Klarvatten Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Klarvatten Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Klarvatten Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Klarvatten Edmonton

Batt Insulation Klarvatten Edmonton: your questions answered

My room is cold and draughty. Will batts fix it?: Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.
Can the rafter bays be filled right up?: Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.
Will insulating an interior wall help with noise?: Yes, noticeably for voices and television, even when sound was not the reason for the job. If a bedroom or office wall is open anyway, upgrading that cavity to a denser batt costs very little on top.
Why is my Klarvatten basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.
Does the garage wall need anything special?: Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.
What about the wiring in the wall?: The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Klarvatten Edmonton

Batt insulation in Klarvatten, fitted rather than stuffed