Do you install the vapour barrier as well?

Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

Do you insulate knee walls and attic hatches?

Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.

Does the garage wall need anything special?

Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.

Can you fill my vaulted ceiling completely?

No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.

Faced or unfaced batts?

One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Batt Insulation Grovenor Edmonton | Wall Batts

Batt insulation in Grovenor, fitted rather than stuffed

Most of what separates good batt work from bad in Grovenor is invisible once the drywall is on. That is exactly why it is worth doing carefully: nobody can inspect it later without opening the wall, and the difference shows up as a cold room rather than as a visible defect.

Rim joists insulated and air-sealed
Odd bays cut to fit rather than packed
Vapour control detailed before the board goes on
Batts friction-fit to full cavity width, not compressed
Mineral wool where fire or sound performance matters
Split and fitted around wiring and electrical boxes

Friction fit, not stapled tight

How a batt is meant to sit

An unfaced batt holds itself in an Grovenor bay by friction across its full width, touching the framing on both sides and the sheathing behind.

The common shortcut

Pulling a faced batt tight and stapling the flanges to the face of the stud, which dishes the middle and leaves a void behind. It looks tidy from the room and performs worse than it measures.

Grovenor drywall in context

About Grovenor

Lying in the City's west end, parts of Grovenor date back to the 1910s.

What we see in Grovenor

In Grovenor the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Garage-to-house walls and ceilings

Two jobs at once

The wall between an Grovenor garage and the house, and the ceiling under living space, usually need a fire separation as well as insulation. The two have to be planned together because the board and the assembly are specified.

Sequencing

Insulation and vapour control go in, get inspected, then the rated board goes on. Doing it in the wrong order means opening a finished rated assembly, which is the expensive way to discover the sequence.

Insulating around plumbing on an exterior wall

Pipes belong on the warm side

A water line run in an Grovenor exterior wall cavity with the batt behind it is sitting on the cold side of the insulation. In February that is a freeze risk.

What we do

Wherever the plumbing allows, the insulation goes behind the pipe so the pipe stays in the heated space. Where it does not, we flag it rather than boarding over a line we know is exposed.

Cathedral ceilings and the ventilation gap

Do not fill it to the deck

In a vaulted Grovenor ceiling there has to be an air channel between the insulation and the roof sheathing. Packing batts tight to the deck closes it, and the roof has no way to dry.

What that costs later

Damp sheathing, mould and in the worst cases rot — none of it visible until it is expensive. The batt is sized so the channel stays open, which means accepting slightly less insulation depth in exchange for a roof that lasts.

Faced, unfaced, and the vapour question

Two systems

A kraft-faced batt carries its own vapour retarder; unfaced batts are paired with a separate poly barrier over the whole wall.

Why it matters here

Using both in the same Grovenor assembly can trap moisture between two retarders. We pick one system for the wall and stay with it rather than mixing what is on the shelf.

Rim joists, the coldest part of a Grovenor basement

Small area, large loss

The rim joist is the band of framing where the floor meets the foundation. It is thin, it is directly exposed to outside, and in most Grovenor basements it is either bare or has a batt tucked loosely against it.

Air sealing first

A batt alone against a rim joist can trap moist air against a cold surface. The joint gets sealed first, then insulated, so warm household air is not reaching the cold band behind the insulation.

How it works

Simple, clean, on schedule — Batt Insulation in Grovenor Edmonton

Free quote

We come out to your Grovenor Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Grovenor Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Grovenor Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Grovenor Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Grovenor Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Grovenor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Grovenor Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Grovenor Edmonton

Batt Insulation Grovenor Edmonton: your questions answered

Do you install the vapour barrier as well?: Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.
Do you insulate knee walls and attic hatches?: Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.
Does the garage wall need anything special?: Usually yes — a fire separation as well as insulation, planned together because the board is specified. Insulation and vapour control go in and get inspected, then the rated board goes on.
Can you fill my vaulted ceiling completely?: No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.
Faced or unfaced batts?: One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Grovenor Edmonton

Batt insulation in Grovenor, fitted rather than stuffed