Can the rafter bays be filled right up?

Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.

Do you insulate knee walls and attic hatches?

Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.

Why is my Greenfield basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Should batts be stapled tight to the studs?

The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Does it matter if the batt is squashed in a bit?

Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Greenfield bays and cut to fit rather than forcing a standard batt in.

Batt Insulation Greenfield Edmonton | Wall Batts

Mineral wool and fibreglass batts in Greenfield walls and ceilings

A batt only performs if it fills the cavity completely and is not squashed. In Greenfield the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Mineral wool where fire or sound performance matters
Split and fitted around wiring and electrical boxes
Rim joists insulated and air-sealed
Batts friction-fit to full cavity width, not compressed
Vapour control detailed before the board goes on
Odd bays cut to fit rather than packed

Rim joists, the coldest part of a Greenfield basement

Small area, large loss

The rim joist is the band of framing where the floor meets the foundation. It is thin, it is directly exposed to outside, and in most Greenfield basements it is either bare or has a batt tucked loosely against it.

Air sealing first

A batt alone against a rim joist can trap moist air against a cold surface. The joint gets sealed first, then insulated, so warm household air is not reaching the cold band behind the insulation.

Greenfield drywall in context

About Greenfield

This area was named for Herbert Greenfield, leader of the United Farmers Party and Premier of Alberta from 1921 to 1925.

What we see in Greenfield

In Greenfield the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Cutting to the bay, not the label

Real framing is not nominal

Greenfield walls, especially in older homes and renovations, carry bays that are wider or narrower than standard, plus cripples, blocking and services.

What we do

Measure and cut. A batt forced into a narrow bay is compressed and underperforms; one left short in a wide bay leaves a gap that convects. Both are invisible after boarding.

Handling, dust and leaving it clean

Practical realities

Batt work makes airborne fibre and it settles everywhere if the space is not controlled.

How the site is run

Covered openings, the crew in proper protection, offcuts bagged rather than swept into the cavity, and a vacuum through the Greenfield space at the end of the day rather than at the end of the job.

Friction fit, not stapled tight

How a batt is meant to sit

An unfaced batt holds itself in an Greenfield bay by friction across its full width, touching the framing on both sides and the sheathing behind.

The common shortcut

Pulling a faced batt tight and stapling the flanges to the face of the stud, which dishes the middle and leaves a void behind. It looks tidy from the room and performs worse than it measures.

Attic hatches, knee walls and the bits at the edges

Small areas, outsized effect

Knee walls in a Greenfield storey-and-a-half, the back of an attic hatch and the ends of joist bays are commonly left bare because they are awkward.

Why we do them anyway

They are direct openings between heated and unheated space. A wall insulated to a high standard with an uninsulated knee wall beside it performs like the weaker of the two, and those edges are where cold rooms usually trace back to.

Wiring, boxes and the gaps behind them

Where the cold gets in

The fastest way to ruin a wall in Greenfield is to stuff the batt behind the wiring and the electrical boxes. It leaves an uninsulated void exactly where there is already a hole in the vapour barrier.

Split, do not stuff

The batt is split so half sits behind the cable and half in front, and it is cut around boxes rather than compressed past them. It is slower and it is the difference between a wall that performs and one that only looks insulated.

How it works

Simple, clean, on schedule — Batt Insulation in Greenfield Edmonton

Free quote

We come out to your Greenfield Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Greenfield Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Greenfield Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Greenfield Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Greenfield Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Greenfield Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Greenfield Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Greenfield Edmonton

Batt Insulation Greenfield Edmonton: your questions answered

Can the rafter bays be filled right up?: Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.
Do you insulate knee walls and attic hatches?: Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.
Why is my Greenfield basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.
Should batts be stapled tight to the studs?: The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Does it matter if the batt is squashed in a bit?: Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Greenfield bays and cut to fit rather than forcing a standard batt in.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Greenfield Edmonton

Mineral wool and fibreglass batts in Greenfield walls and ceilings