Can the rafter bays be filled right up?

Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.

My room is cold and draughty. Will batts fix it?

Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.

Do you insulate knee walls and attic hatches?

Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.

Do you install the vapour barrier as well?

Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Should batts be stapled tight to the studs?

The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.

Batt Insulation Fulton Place Edmonton | Wall Batts

Batt insulation in Fulton Place, fitted rather than stuffed

Most of what separates good batt work from bad in Fulton Place is invisible once the drywall is on. That is exactly why it is worth doing carefully: nobody can inspect it later without opening the wall, and the difference shows up as a cold room rather than as a visible defect.

Rim joists insulated and air-sealed
Batts friction-fit to full cavity width, not compressed
Mineral wool where fire or sound performance matters
Split and fitted around wiring and electrical boxes
Odd bays cut to fit rather than packed
Vapour control detailed before the board goes on

Faced, unfaced, and the vapour question

Two systems

A kraft-faced batt carries its own vapour retarder; unfaced batts are paired with a separate poly barrier over the whole wall.

Why it matters here

Using both in the same Fulton Place assembly can trap moisture between two retarders. We pick one system for the wall and stay with it rather than mixing what is on the shelf.

Fulton Place drywall in context

About Fulton Place

Named for the creek which runs through the ravine on its west boundary, Fulton Place lies east of the downtown core and developed in the 1950s.

What we see in Fulton Place

In Fulton Place the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Cutting to the bay, not the label

Real framing is not nominal

Fulton Place walls, especially in older homes and renovations, carry bays that are wider or narrower than standard, plus cripples, blocking and services.

What we do

Measure and cut. A batt forced into a narrow bay is compressed and underperforms; one left short in a wide bay leaves a gap that convects. Both are invisible after boarding.

Vapour control, and why the order matters

Warm side, always

In Fulton Place the vapour barrier goes on the warm side of the insulation. Putting it in the wrong place, or having two of them, traps moisture inside the assembly where it cannot dry.

Sequencing

Insulation is completed and inspected before the barrier goes on, and the barrier is sealed at penetrations before boarding. Once drywall is up, none of this can be corrected without taking the wall apart again.

Insulating a Fulton Place basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Fulton Place is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Fulton Place basement smells musty a year later.

Sound as a side effect of insulating

You get some for free

Filling an interior Fulton Place wall cavity with batts noticeably reduces voice and television noise between rooms, even when sound was not the reason for the job.

Where to spend a little more

If a bedroom, office or bathroom wall is being opened anyway, upgrading that specific cavity to a denser acoustic or mineral wool batt costs very little on top of work already happening. We will point out which walls those are while we are quoting.

What batts will not fix

Insulation is not air sealing

If a Fulton Place room is cold because of draughts around windows, an unsealed rim joist or gaps at the top plate, filling the cavity with batts will disappoint you.

Why we say it first

We would rather diagnose the draught and quote the sealing than sell you insulation that does not solve the complaint. The two jobs go together, and the sealing is usually the cheaper half.

How it works

Simple, clean, on schedule — Batt Insulation in Fulton Place Edmonton

Free quote

We come out to your Fulton Place Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Fulton Place Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Fulton Place Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Fulton Place Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Fulton Place Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Fulton Place Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Fulton Place Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Fulton Place Edmonton

Batt Insulation Fulton Place Edmonton: your questions answered

Can the rafter bays be filled right up?: Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.
My room is cold and draughty. Will batts fix it?: Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.
Do you insulate knee walls and attic hatches?: Yes, and they matter more than their size suggests. They are direct openings between heated and unheated space, and a well-insulated wall next to a bare knee wall performs like the weaker of the two.
Do you install the vapour barrier as well?: Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
Should batts be stapled tight to the studs?: The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Fulton Place Edmonton

Batt insulation in Fulton Place, fitted rather than stuffed