What about the pipes in my exterior wall?

Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.

Can the rafter bays be filled right up?

Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.

Can batts go straight against my Falconer Heights basement concrete?

No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.

Why is my Falconer Heights basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Batt Insulation Falconer Heights Edmonton | Wall Batts

Mineral wool and fibreglass batts in Falconer Heights walls and ceilings

A batt only performs if it fills the cavity completely and is not squashed. In Falconer Heights the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Vapour control detailed before the board goes on
Split and fitted around wiring and electrical boxes
Rim joists insulated and air-sealed
Batts friction-fit to full cavity width, not compressed
Odd bays cut to fit rather than packed
Mineral wool where fire or sound performance matters

Kneewalls and the rooms in the roof

A cold face nobody sees

A kneewall in an Falconer Heights storey-and-a-half has attic space directly behind it, so the back of that batt is exposed to outdoor air.

What it needs

The batt supported and its back face covered, rather than left open to the attic where air washes straight through it. Uncovered kneewall insulation is one of the most common finds in older homes.

Falconer Heights drywall in context

About Falconer Heights

Falconer, who was involved in the formation of Edmonton's Names Advisory Committee in the mid 1950s and served on the committee until 1979.

What we see in Falconer Heights

In Falconer Heights the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Friction fit, not stapled tight

How a batt is meant to sit

An unfaced batt holds itself in an Falconer Heights bay by friction across its full width, touching the framing on both sides and the sheathing behind.

The common shortcut

Pulling a faced batt tight and stapling the flanges to the face of the stud, which dishes the middle and leaves a void behind. It looks tidy from the room and performs worse than it measures.

Mineral wool against fibreglass in Falconer Heights

Different tools

Fibreglass batts are the common choice and perform well when fitted properly. Mineral wool is denser, holds its shape better in a cavity, handles fire differently and performs noticeably better for sound.

Where we would spend the difference

Party walls, bedrooms, mechanical rooms and any assembly where sound or fire matters. For an ordinary interior partition in Falconer Heights, fibreglass fitted well beats mineral wool fitted badly.

Insulating a Falconer Heights basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Falconer Heights is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Falconer Heights basement smells musty a year later.

What batts will not fix

Insulation is not air sealing

If a Falconer Heights room is cold because of draughts around windows, an unsealed rim joist or gaps at the top plate, filling the cavity with batts will disappoint you.

Why we say it first

We would rather diagnose the draught and quote the sealing than sell you insulation that does not solve the complaint. The two jobs go together, and the sealing is usually the cheaper half.

Compression is the most common Falconer Heights mistake

A squashed batt is a weaker batt

Batt insulation works because of the still air trapped in it. Compress it into a narrower bay and you lose a meaningful share of its performance while paying for the full product.

The fix is measurement

Falconer Heights framing is not always at a standard spacing, especially in older homes and renovations. We measure the bays and cut to fit rather than forcing a standard batt into a non-standard cavity.

How it works

Simple, clean, on schedule — Batt Insulation in Falconer Heights Edmonton

Free quote

We come out to your Falconer Heights Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Falconer Heights Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Falconer Heights Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Falconer Heights Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Falconer Heights Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Falconer Heights Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Falconer Heights Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Falconer Heights Edmonton

Batt Insulation Falconer Heights Edmonton: your questions answered

What about the pipes in my exterior wall?: Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.
Can the rafter bays be filled right up?: Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.
Can batts go straight against my Falconer Heights basement concrete?: No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.
Why is my Falconer Heights basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Falconer Heights Edmonton

Mineral wool and fibreglass batts in Falconer Heights walls and ceilings