My room is cold and draughty. Will batts fix it?

Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Can batts go straight against my Elmwood basement concrete?

No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Do you cut batts to fit?

Yes. Real Elmwood framing carries bays wider or narrower than nominal, plus cripples and blocking. Forced batts are compressed and underperform; short ones leave gaps that convect. Both are invisible after boarding.

What about the wiring in the wall?

The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Batt Insulation Elmwood Edmonton | Wall Batts

Batt insulation in Elmwood before the vapour barrier goes on

Most of what separates good batt work from bad in Elmwood is invisible once the drywall is on. That is exactly why it is worth doing carefully: nobody can inspect it later without opening the wall, and the difference shows up as a cold room rather than as a visible defect.

Odd bays cut to fit rather than packed
Split and fitted around wiring and electrical boxes
Vapour control detailed before the board goes on
Mineral wool where fire or sound performance matters
Rim joists insulated and air-sealed
Batts friction-fit to full cavity width, not compressed

Vapour control, and why the order matters

Warm side, always

In Elmwood the vapour barrier goes on the warm side of the insulation. Putting it in the wrong place, or having two of them, traps moisture inside the assembly where it cannot dry.

Sequencing

Insulation is completed and inspected before the barrier goes on, and the barrier is sealed at penetrations before boarding. Once drywall is up, none of this can be corrected without taking the wall apart again.

Garage-to-house walls and ceilings

Two jobs at once

The wall between an Elmwood garage and the house, and the ceiling under living space, usually need a fire separation as well as insulation. The two have to be planned together because the board and the assembly are specified.

Sequencing

Insulation and vapour control go in, get inspected, then the rated board goes on. Doing it in the wrong order means opening a finished rated assembly, which is the expensive way to discover the sequence.

Faced, unfaced, and the vapour question

Two systems

A kraft-faced batt carries its own vapour retarder; unfaced batts are paired with a separate poly barrier over the whole wall.

Why it matters here

Using both in the same Elmwood assembly can trap moisture between two retarders. We pick one system for the wall and stay with it rather than mixing what is on the shelf.

Cathedral ceilings and the ventilation gap

Do not fill it to the deck

In a vaulted Elmwood ceiling there has to be an air channel between the insulation and the roof sheathing. Packing batts tight to the deck closes it, and the roof has no way to dry.

What that costs later

Damp sheathing, mould and in the worst cases rot — none of it visible until it is expensive. The batt is sized so the channel stays open, which means accepting slightly less insulation depth in exchange for a roof that lasts.

Cathedral ceilings and leaving the air gap

Do not fill it completely

A vented cathedral ceiling in an Elmwood home needs a clear air channel between the insulation and the roof sheathing.

Why

Packing the rafter bay full removes the ventilation that keeps the deck cold and dry, which is how a warm sloped ceiling ends up with a damp deck. Baffles hold the channel open.

Sound as a side effect of insulating

You get some for free

Filling an interior Elmwood wall cavity with batts noticeably reduces voice and television noise between rooms, even when sound was not the reason for the job.

Where to spend a little more

If a bedroom, office or bathroom wall is being opened anyway, upgrading that specific cavity to a denser acoustic or mineral wool batt costs very little on top of work already happening. We will point out which walls those are while we are quoting.

How it works

Simple, clean, on schedule — Batt Insulation in Elmwood Edmonton

Free quote

We come out to your Elmwood Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Elmwood Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Elmwood Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Elmwood Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Elmwood Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Elmwood Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Elmwood Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Elmwood Edmonton

Batt Insulation Elmwood Edmonton: your questions answered

My room is cold and draughty. Will batts fix it?: Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
Can batts go straight against my Elmwood basement concrete?: No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Do you cut batts to fit?: Yes. Real Elmwood framing carries bays wider or narrower than nominal, plus cripples and blocking. Forced batts are compressed and underperform; short ones leave gaps that convect. Both are invisible after boarding.
What about the wiring in the wall?: The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Elmwood Edmonton

Batt insulation in Elmwood before the vapour barrier goes on