Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

My room is cold and draughty. Will batts fix it?

Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.

What about the pipes in my exterior wall?

Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.

Do you cut batts to fit?

Yes. Real Cloverdale framing carries bays wider or narrower than nominal, plus cripples and blocking. Forced batts are compressed and underperform; short ones leave gaps that convect. Both are invisible after boarding.

Do you install the vapour barrier as well?

Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

What about the wiring in the wall?

The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Batt Insulation Cloverdale Edmonton | Wall Batts

Batt insulation in Cloverdale, fitted rather than stuffed

Most of what separates good batt work from bad in Cloverdale is invisible once the drywall is on. That is exactly why it is worth doing carefully: nobody can inspect it later without opening the wall, and the difference shows up as a cold room rather than as a visible defect.

Batts friction-fit to full cavity width, not compressed
Rim joists insulated and air-sealed
Vapour control detailed before the board goes on
Odd bays cut to fit rather than packed
Mineral wool where fire or sound performance matters
Split and fitted around wiring and electrical boxes

Batts around ducts and services

What is on the cold side

A duct or pipe run through an exterior Cloverdale bay must have insulation behind it, between it and the outside, not merely stuffed in around it.

Consequence of getting it wrong

A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question. It is worth the extra few minutes on each bay.

Cloverdale drywall in context

About Cloverdale

Cloverdale is situated along the south bank of the North Saskatchewan River near the centre of the city.

What we see in Cloverdale

In Cloverdale the drywall work is settling cracks/nail pops, basement development, builder-grade L4->L5 upgrades. We confirm what your home actually needs on site, in writing, before anything starts.

Cathedral ceilings and leaving the air gap

Do not fill it completely

A vented cathedral ceiling in an Cloverdale home needs a clear air channel between the insulation and the roof sheathing.

Why

Packing the rafter bay full removes the ventilation that keeps the deck cold and dry, which is how a warm sloped ceiling ends up with a damp deck. Baffles hold the channel open.

Cathedral ceilings and the ventilation gap

Do not fill it to the deck

In a vaulted Cloverdale ceiling there has to be an air channel between the insulation and the roof sheathing. Packing batts tight to the deck closes it, and the roof has no way to dry.

What that costs later

Damp sheathing, mould and in the worst cases rot — none of it visible until it is expensive. The batt is sized so the channel stays open, which means accepting slightly less insulation depth in exchange for a roof that lasts.

Insulating a Cloverdale basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Cloverdale is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Cloverdale basement smells musty a year later.

Rim joists, the coldest part of a Cloverdale basement

Small area, large loss

The rim joist is the band of framing where the floor meets the foundation. It is thin, it is directly exposed to outside, and in most Cloverdale basements it is either bare or has a batt tucked loosely against it.

Air sealing first

A batt alone against a rim joist can trap moist air against a cold surface. The joint gets sealed first, then insulated, so warm household air is not reaching the cold band behind the insulation.

Wiring, boxes and the gaps behind them

Where the cold gets in

The fastest way to ruin a wall in Cloverdale is to stuff the batt behind the wiring and the electrical boxes. It leaves an uninsulated void exactly where there is already a hole in the vapour barrier.

Split, do not stuff

The batt is split so half sits behind the cable and half in front, and it is cut around boxes rather than compressed past them. It is slower and it is the difference between a wall that performs and one that only looks insulated.

How it works

Simple, clean, on schedule — Batt Insulation in Cloverdale Edmonton

Free quote

We come out to your Cloverdale Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Cloverdale Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Cloverdale Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Cloverdale Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Cloverdale Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Cloverdale Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Cloverdale Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Cloverdale Edmonton

Batt Insulation Cloverdale Edmonton: your questions answered

Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
My room is cold and draughty. Will batts fix it?: Probably not on their own. Draughts around windows, an unsealed rim joist or gaps at the top plate are air leaks, and insulation does not stop air. We would rather diagnose the draught and quote the sealing, which is usually the cheaper half.
What about the pipes in my exterior wall?: Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.
Do you cut batts to fit?: Yes. Real Cloverdale framing carries bays wider or narrower than nominal, plus cripples and blocking. Forced batts are compressed and underperform; short ones leave gaps that convect. Both are invisible after boarding.
Do you install the vapour barrier as well?: Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.
What about the wiring in the wall?: The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Cloverdale Edmonton

Batt insulation in Cloverdale, fitted rather than stuffed