Should batts be stapled tight to the studs?

The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.

Do you install the vapour barrier as well?

Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

Faced or unfaced batts?

One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.

Can you fill my vaulted ceiling completely?

No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.

Can the rafter bays be filled right up?

Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.

Why is my Carlton basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Batt Insulation Carlton Edmonton | Wall Batts

Mineral wool and fibreglass batts in Carlton walls and ceilings

A batt only performs if it fills the cavity completely and is not squashed. In Carlton the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Mineral wool where fire or sound performance matters
Rim joists insulated and air-sealed
Vapour control detailed before the board goes on
Batts friction-fit to full cavity width, not compressed
Split and fitted around wiring and electrical boxes
Odd bays cut to fit rather than packed

Cutting to the bay, not the label

Real framing is not nominal

Carlton walls, especially in older homes and renovations, carry bays that are wider or narrower than standard, plus cripples, blocking and services.

What we do

Measure and cut. A batt forced into a narrow bay is compressed and underperforms; one left short in a wide bay leaves a gap that convects. Both are invisible after boarding.

Carlton drywall in context

About Carlton

Carlton is named after Fort Carlton There are several natural areas within the neighbourhood, including a woodlot containing indigenous species located in the northwestern portion of the neighbourhood.

What we see in Carlton

In Carlton the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Kneewalls and the rooms in the roof

A cold face nobody sees

A kneewall in an Carlton storey-and-a-half has attic space directly behind it, so the back of that batt is exposed to outdoor air.

What it needs

The batt supported and its back face covered, rather than left open to the attic where air washes straight through it. Uncovered kneewall insulation is one of the most common finds in older homes.

What batts will not fix

Insulation is not air sealing

If a Carlton room is cold because of draughts around windows, an unsealed rim joist or gaps at the top plate, filling the cavity with batts will disappoint you.

Why we say it first

We would rather diagnose the draught and quote the sealing than sell you insulation that does not solve the complaint. The two jobs go together, and the sealing is usually the cheaper half.

Handling, dust and leaving it clean

Practical realities

Batt work makes airborne fibre and it settles everywhere if the space is not controlled.

How the site is run

Covered openings, the crew in proper protection, offcuts bagged rather than swept into the cavity, and a vacuum through the Carlton space at the end of the day rather than at the end of the job.

Compression is the most common Carlton mistake

A squashed batt is a weaker batt

Batt insulation works because of the still air trapped in it. Compress it into a narrower bay and you lose a meaningful share of its performance while paying for the full product.

The fix is measurement

Carlton framing is not always at a standard spacing, especially in older homes and renovations. We measure the bays and cut to fit rather than forcing a standard batt into a non-standard cavity.

Attic hatches, knee walls and the bits at the edges

Small areas, outsized effect

Knee walls in a Carlton storey-and-a-half, the back of an attic hatch and the ends of joist bays are commonly left bare because they are awkward.

Why we do them anyway

They are direct openings between heated and unheated space. A wall insulated to a high standard with an uninsulated knee wall beside it performs like the weaker of the two, and those edges are where cold rooms usually trace back to.

How it works

Simple, clean, on schedule — Batt Insulation in Carlton Edmonton

Free quote

We come out to your Carlton Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Carlton Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Carlton Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Carlton Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Carlton Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Carlton Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Carlton Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Carlton Edmonton

Batt Insulation Carlton Edmonton: your questions answered

Should batts be stapled tight to the studs?: The face-stapling shortcut dishes the middle of the batt and leaves a void behind it. A batt should sit by friction across its full width, touching framing on both sides and the sheathing behind.
Do you install the vapour barrier as well?: Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.
Faced or unfaced batts?: One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.
Can you fill my vaulted ceiling completely?: No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.
Can the rafter bays be filled right up?: Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.
Why is my Carlton basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Carlton Edmonton

Mineral wool and fibreglass batts in Carlton walls and ceilings