Can the rafter bays be filled right up?

Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.

What about the wiring in the wall?

The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Why is my Boyle Street basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

Do you install the vapour barrier as well?

Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

Batt Insulation Boyle Street Edmonton | Wall Batts

Batt insulation in Boyle Street before the vapour barrier goes on

Most of what separates good batt work from bad in Boyle Street is invisible once the drywall is on. That is exactly why it is worth doing carefully: nobody can inspect it later without opening the wall, and the difference shows up as a cold room rather than as a visible defect.

Rim joists insulated and air-sealed
Mineral wool where fire or sound performance matters
Odd bays cut to fit rather than packed
Batts friction-fit to full cavity width, not compressed
Vapour control detailed before the board goes on
Split and fitted around wiring and electrical boxes

What batts will not fix

Insulation is not air sealing

If a Boyle Street room is cold because of draughts around windows, an unsealed rim joist or gaps at the top plate, filling the cavity with batts will disappoint you.

Why we say it first

We would rather diagnose the draught and quote the sealing than sell you insulation that does not solve the complaint. The two jobs go together, and the sealing is usually the cheaper half.

Boyle Street drywall in context

About Boyle Street

The hub of Edmonton's early commercial district, Boyle Street was recorded on a map of the newly created town of Edmonton in 1892.

What we see in Boyle Street

In Boyle Street the drywall work is verify dominant band before writing notes. We confirm what your home actually needs on site, in writing, before anything starts.

Sound as a side effect of insulating

You get some for free

Filling an interior Boyle Street wall cavity with batts noticeably reduces voice and television noise between rooms, even when sound was not the reason for the job.

Where to spend a little more

If a bedroom, office or bathroom wall is being opened anyway, upgrading that specific cavity to a denser acoustic or mineral wool batt costs very little on top of work already happening. We will point out which walls those are while we are quoting.

Attic hatches, knee walls and the bits at the edges

Small areas, outsized effect

Knee walls in a Boyle Street storey-and-a-half, the back of an attic hatch and the ends of joist bays are commonly left bare because they are awkward.

Why we do them anyway

They are direct openings between heated and unheated space. A wall insulated to a high standard with an uninsulated knee wall beside it performs like the weaker of the two, and those edges are where cold rooms usually trace back to.

Insulating a Boyle Street basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Boyle Street is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Boyle Street basement smells musty a year later.

Cathedral ceilings and leaving the air gap

Do not fill it completely

A vented cathedral ceiling in an Boyle Street home needs a clear air channel between the insulation and the roof sheathing.

Why

Packing the rafter bay full removes the ventilation that keeps the deck cold and dry, which is how a warm sloped ceiling ends up with a damp deck. Baffles hold the channel open.

Friction fit, not stapled tight

How a batt is meant to sit

An unfaced batt holds itself in an Boyle Street bay by friction across its full width, touching the framing on both sides and the sheathing behind.

The common shortcut

Pulling a faced batt tight and stapling the flanges to the face of the stud, which dishes the middle and leaves a void behind. It looks tidy from the room and performs worse than it measures.

How it works

Simple, clean, on schedule — Batt Insulation in Boyle Street Edmonton

Free quote

We come out to your Boyle Street Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Boyle Street Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Boyle Street Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Boyle Street Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Boyle Street Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Boyle Street Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Boyle Street Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Boyle Street Edmonton

Batt Insulation Boyle Street Edmonton: your questions answered

Can the rafter bays be filled right up?: Not in a vented cathedral ceiling. A clear air channel has to stay between insulation and roof sheathing, held open with baffles, or the deck cannot stay cold and dry.
What about the wiring in the wall?: The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.
Why is my Boyle Street basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
Do you install the vapour barrier as well?: Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Boyle Street Edmonton

Batt insulation in Boyle Street before the vapour barrier goes on