Can you fill my vaulted ceiling completely?

No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.

Faced or unfaced batts?

One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.

Can batts go straight against my Bisset basement concrete?

No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.

What about the wiring in the wall?

The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

What about the pipes in my exterior wall?

Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.

Why is my Bisset basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Batt Insulation Bisset Edmonton | Wall Batts

Batt insulation in Bisset before the vapour barrier goes on

Most of what separates good batt work from bad in Bisset is invisible once the drywall is on. That is exactly why it is worth doing carefully: nobody can inspect it later without opening the wall, and the difference shows up as a cold room rather than as a visible defect.

Rim joists insulated and air-sealed
Batts friction-fit to full cavity width, not compressed
Mineral wool where fire or sound performance matters
Vapour control detailed before the board goes on
Split and fitted around wiring and electrical boxes
Odd bays cut to fit rather than packed

Insulating an existing Bisset wall without opening it

The honest limits

Batts need an open cavity. If a Bisset wall is finished and staying finished, batts are not the product — that is a job for a blown-in or injected material, or for adding insulation on the room side.

What we say

We would rather tell you batts are the wrong answer for a closed wall than sell you a partial job. Where the wall is already open for other work, that is the moment to insulate properly.

Bisset drywall in context

About Bisset

Bisset is named for Judge Athelstan Bisset, Q.C.

What we see in Bisset

In Bisset the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Cathedral ceilings and leaving the air gap

Do not fill it completely

A vented cathedral ceiling in an Bisset home needs a clear air channel between the insulation and the roof sheathing.

Why

Packing the rafter bay full removes the ventilation that keeps the deck cold and dry, which is how a warm sloped ceiling ends up with a damp deck. Baffles hold the channel open.

Sound as a side effect of insulating

You get some for free

Filling an interior Bisset wall cavity with batts noticeably reduces voice and television noise between rooms, even when sound was not the reason for the job.

Where to spend a little more

If a bedroom, office or bathroom wall is being opened anyway, upgrading that specific cavity to a denser acoustic or mineral wool batt costs very little on top of work already happening. We will point out which walls those are while we are quoting.

Mineral wool against fibreglass in Bisset

Different tools

Fibreglass batts are the common choice and perform well when fitted properly. Mineral wool is denser, holds its shape better in a cavity, handles fire differently and performs noticeably better for sound.

Where we would spend the difference

Party walls, bedrooms, mechanical rooms and any assembly where sound or fire matters. For an ordinary interior partition in Bisset, fibreglass fitted well beats mineral wool fitted badly.

Kneewalls and the rooms in the roof

A cold face nobody sees

A kneewall in an Bisset storey-and-a-half has attic space directly behind it, so the back of that batt is exposed to outdoor air.

What it needs

The batt supported and its back face covered, rather than left open to the attic where air washes straight through it. Uncovered kneewall insulation is one of the most common finds in older homes.

Insulating a Bisset basement wall against concrete

Not the same as a framed wall above grade

A basement wall in Bisset is concrete, cold, and can carry moisture from the ground. Batts pressed straight against bare concrete sit in exactly the wrong place: the cold side, where any moisture they pick up cannot dry.

How the assembly works

The framing is held off the concrete, or a rigid layer goes against the wall first, so the batts sit in a cavity that stays on the warm side. Getting that order wrong is the usual reason a finished Bisset basement smells musty a year later.

How it works

Simple, clean, on schedule — Batt Insulation in Bisset Edmonton

Free quote

We come out to your Bisset Edmonton property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Bisset Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Bisset Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Bisset Edmonton home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Bisset Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Bisset Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Bisset Edmonton.

Read our reviews on Google

FAQ — Batt Insulation Bisset Edmonton

Batt Insulation Bisset Edmonton: your questions answered

Can you fill my vaulted ceiling completely?: No, and it matters. There has to be an air channel between the insulation and the roof sheathing so the roof can dry. Packing it tight leads to damp sheathing and eventually rot, none of it visible until it is expensive.
Faced or unfaced batts?: One system per wall. Faced batts carry their own vapour retarder; unfaced are paired with a separate poly barrier. Using both in one assembly can trap moisture between two retarders.
Can batts go straight against my Bisset basement concrete?: No. Against bare concrete they sit on the cold side where moisture cannot dry, and that is the usual reason a finished basement smells musty a year later. The framing is held off, or a rigid layer goes on first, so the batts stay on the warm side.
What about the wiring in the wall?: The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.
What about the pipes in my exterior wall?: Insulation goes behind them, between the pipe and the outside, not stuffed in around them. A water line on the cold side of the batt is a freeze risk in an Alberta winter, not just an efficiency question.
Why is my Bisset basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Batt Insulation Bisset Edmonton

Batt insulation in Bisset before the vapour barrier goes on