Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

I store things in my attic. Can I keep doing that?

Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.

Can you blow insulation over my pot lights?

Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.

Do I need to seal before adding insulation?

Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

How much will this save me on heating?

We will not put a percentage on it. Too much depends on your air leakage, windows and furnace. We will tell you what depth you have now, what you would have after, and where the leaks are — those we can actually measure.

Attic Insulation Schonsee Edmonton | Attic Top-Up

Attic insulation in Schonsee: air seal first, then blow

The most common mistake in an Schonsee attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Blown-in loose-fill to the depth your permit specifies
Depth markers left in place so the result is verifiable
Attic hatch insulated and weatherstripped
Existing insulation levelled before the top-up
Air sealing at pot lights, top plates and the attic hatch
Baffles kept clear so the soffit vents still breathe

Ice damming and what the attic has to do with it

A heat problem, not a gutter problem

Ice at the eaves on an Schonsee roof usually means heat is escaping into the attic, melting snow on the upper roof, and that meltwater refreezing over the cold overhang.

Where the fix actually is

More heat tape rarely solves it. Sealing the air leaks and getting even insulation coverage right out to the eaves is what lowers the deck temperature. That is why we look at the attic when someone calls about ice, not at the roofline.

Schonsee drywall in context

About Schonsee

The name Schonsee is derived from the German word "schon", meaning beautiful, and "see" meaning lake.

What we see in Schonsee

In Schonsee the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Pot lights, and which ones can be covered

Not all fixtures are equal

Older recessed fixtures in Schonsee ceilings need clearance and cannot be buried. Newer IC-rated fixtures are built to be in contact with insulation.

What we check

We identify what is installed before blowing. Where fixtures cannot be covered, they need boxing or replacing — and each one is also a significant air leak, so they are usually the first thing sealed regardless of type.

Storage in the attic

An honest trade-off

Boards laid over the joists in an Schonsee attic compress the insulation beneath them and create a thin band right through the middle of the ceiling.

What we suggest

A raised platform over a limited area if storage is genuinely needed, so the insulation depth continues underneath it. Or accepting that a full-depth attic is not also a storage room.

Storage in the attic and the insulation you lose

Boards over joists compress everything

Where a Schonsee homeowner has laid plywood across the joists for storage, the insulation beneath is squashed to joist depth. That strip performs at a fraction of the rest of the attic.

Options

Either the storage area is raised on a platform above the finished insulation depth, or it is accepted as a deliberately weaker zone kept as small as possible. What does not work is topping up around it and pretending the platform is not there.

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Schonsee attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

Adding to what is already there

You rarely start empty

Most Schonsee attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

How it works

Simple, clean, on schedule — Attic Insulation in Schonsee Edmonton

Free quote

We come out to your Schonsee Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Schonsee Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Schonsee Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Schonsee Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Schonsee Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Schonsee Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Schonsee Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Schonsee Edmonton

Attic Insulation Schonsee Edmonton: your questions answered

Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
I store things in my attic. Can I keep doing that?: Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.
Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
Can you blow insulation over my pot lights?: Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.
Do I need to seal before adding insulation?: Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.
How much will this save me on heating?: We will not put a percentage on it. Too much depends on your air leakage, windows and furnace. We will tell you what depth you have now, what you would have after, and where the leaks are — those we can actually measure.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Schonsee Edmonton

Attic insulation in Schonsee: air seal first, then blow