I store things in my attic. Can I keep doing that?

Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.

How much insulation should my Riverview Area attic have?

The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.

My bathroom fan seems to vent into the attic. Is that a problem?

Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Will insulating my attic stop the ice at my eaves?

Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.

Why is the area above my exterior walls always cold?

Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

Attic Insulation Riverview Area Edmonton | Attic Top-Up

Attic top-ups in Riverview Area that hold their depth

Attics in Riverview Area lose depth over time — insulation settles, someone crawls through it for a wiring job, and the corners near the eaves are usually thin to begin with. A top-up is only worth doing if the baffles are clear and the ceiling below is sealed, so that is what we check before quoting.

Attic hatch insulated and weatherstripped
Depth markers left in place so the result is verifiable
Existing insulation levelled before the top-up
Blown-in loose-fill to the depth your permit specifies
Air sealing at pot lights, top plates and the attic hatch
Baffles kept clear so the soffit vents still breathe

Depth, and how to check we delivered it

Verifiable rather than assumed

Blown insulation settles, and depth is easy to claim and hard to check once the hatch is closed. We leave depth markers through the Riverview Area attic so the installed depth can be read off later by anyone.

Even coverage

Depth is also an average — a deep drift in the middle and thin corners is not the same as an even blanket. Coverage to the edges is what actually reduces heat loss.

What we can and cannot tell you about savings

Honest about the number

We will not quote you a percentage off your heating bill. It depends on your current depth, your air leakage, your windows, your furnace and how you heat the house.

What we will say

What the attic has now, what it would have after, and where the leaks are. Those are things we can measure and show you. A savings figure from a contractor who has not seen your utility bills is a sales number, not an estimate.

Attics over additions and vaulted areas

The awkward spaces

An Riverview Area addition often has a shallow attic, a cathedral section or a knee wall, and those areas are where insulation is thinnest and access is worst.

Why they matter disproportionately

They are frequently the coldest rooms in the house, and they are the parts a general top-up misses because the blower cannot reach them. We look at them specifically rather than quoting an average depth across the whole ceiling.

Ice damming and what the attic has to do with it

A heat problem, not a gutter problem

Ice at the eaves on an Riverview Area roof usually means heat is escaping into the attic, melting snow on the upper roof, and that meltwater refreezing over the cold overhang.

Where the fix actually is

More heat tape rarely solves it. Sealing the air leaks and getting even insulation coverage right out to the eaves is what lowers the deck temperature. That is why we look at the attic when someone calls about ice, not at the roofline.

Storage in the attic and the insulation you lose

Boards over joists compress everything

Where a Riverview Area homeowner has laid plywood across the joists for storage, the insulation beneath is squashed to joist depth. That strip performs at a fraction of the rest of the attic.

Options

Either the storage area is raised on a platform above the finished insulation depth, or it is accepted as a deliberately weaker zone kept as small as possible. What does not work is topping up around it and pretending the platform is not there.

The attic hatch nobody insulates

A hole in the ceiling

An uninsulated, unsealed hatch is a direct opening between the heated house and a cold attic, and it is often the single worst detail in an otherwise good Riverview Area ceiling.

Simple fix

An insulated cover with weatherstripping and a dam around the opening so blown insulation does not spill through when it is opened.

How it works

Simple, clean, on schedule — Attic Insulation in Riverview Area Edmonton

Free quote

We come out to your Riverview Area Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Riverview Area Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Riverview Area Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Riverview Area Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Riverview Area Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Riverview Area Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Riverview Area Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Riverview Area Edmonton

Attic Insulation Riverview Area Edmonton: your questions answered

I store things in my attic. Can I keep doing that?: Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.
How much insulation should my Riverview Area attic have?: The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.
My bathroom fan seems to vent into the attic. Is that a problem?: Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.
Will insulating my attic stop the ice at my eaves?: Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.
Why is the area above my exterior walls always cold?: Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Riverview Area Edmonton

Attic top-ups in Riverview Area that hold their depth