Why is the area above my exterior walls always cold?

Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

My bathroom fan seems to vent into the attic. Is that a problem?

Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Do I need to seal before adding insulation?

Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Attic Insulation Parkdale Edmonton | Attic Top-Up

Attic top-ups in Parkdale that hold their depth

The most common mistake in an Parkdale attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Blown-in loose-fill to the depth your permit specifies
Depth markers left in place so the result is verifiable
Attic hatch insulated and weatherstripped
Baffles kept clear so the soffit vents still breathe
Existing insulation levelled before the top-up
Air sealing at pot lights, top plates and the attic hatch

Depth, and how to check we delivered it

Verifiable rather than assumed

Blown insulation settles, and depth is easy to claim and hard to check once the hatch is closed. We leave depth markers through the Parkdale attic so the installed depth can be read off later by anyone.

Even coverage

Depth is also an average — a deep drift in the middle and thin corners is not the same as an even blanket. Coverage to the edges is what actually reduces heat loss.

Parkdale drywall in context

About Parkdale

Parkdale is a low-density residential neighbourhood close to the inner city featuring primarily single-family homes as well as some commercial and industrial areas.

What we see in Parkdale

In Parkdale the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Parkdale attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

Storage in the attic and the insulation you lose

Boards over joists compress everything

Where a Parkdale homeowner has laid plywood across the joists for storage, the insulation beneath is squashed to joist depth. That strip performs at a fraction of the rest of the attic.

Options

Either the storage area is raised on a platform above the finished insulation depth, or it is accepted as a deliberately weaker zone kept as small as possible. What does not work is topping up around it and pretending the platform is not there.

Adding to what is already there

You rarely start empty

Most Parkdale attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Parkdale attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

Insulating a Parkdale attic with knob-and-tube or old wiring

Stop and check first

Some older Parkdale homes still carry active knob-and-tube wiring in the attic. Burying it in insulation is not something we do — it needs an electrician to assess and usually to replace before the attic is filled.

Why we raise it

It is the kind of thing found halfway through a job, and it is far cheaper to find at the quote. If we see it, we tell you and we stop until it is dealt with.

How it works

Simple, clean, on schedule — Attic Insulation in Parkdale Edmonton

Free quote

We come out to your Parkdale Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Parkdale Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Parkdale Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Parkdale Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Parkdale Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Parkdale Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Parkdale Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Parkdale Edmonton

Attic Insulation Parkdale Edmonton: your questions answered

Why is the area above my exterior walls always cold?: Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.
Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.
Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
My bathroom fan seems to vent into the attic. Is that a problem?: Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
Do I need to seal before adding insulation?: Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Parkdale Edmonton

Attic top-ups in Parkdale that hold their depth