How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

How much will this save me on heating?

We will not put a percentage on it. Too much depends on your air leakage, windows and furnace. We will tell you what depth you have now, what you would have after, and where the leaks are — those we can actually measure.

Cellulose or fibreglass?

Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Can I add over the old insulation?

Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.

Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Attic Insulation Oxford Edmonton | Attic Top-Up

Blown-in attic insulation in Oxford, sealed before it is filled

Attics in Oxford lose depth over time — insulation settles, someone crawls through it for a wiring job, and the corners near the eaves are usually thin to begin with. A top-up is only worth doing if the baffles are clear and the ceiling below is sealed, so that is what we check before quoting.

Air sealing at pot lights, top plates and the attic hatch
Depth markers left in place so the result is verifiable
Attic hatch insulated and weatherstripped
Existing insulation levelled before the top-up
Blown-in loose-fill to the depth your permit specifies
Baffles kept clear so the soffit vents still breathe

Ice damming and what the attic has to do with it

A heat problem, not a gutter problem

Ice at the eaves on an Oxford roof usually means heat is escaping into the attic, melting snow on the upper roof, and that meltwater refreezing over the cold overhang.

Where the fix actually is

More heat tape rarely solves it. Sealing the air leaks and getting even insulation coverage right out to the eaves is what lowers the deck temperature. That is why we look at the attic when someone calls about ice, not at the roofline.

Oxford drywall in context

About Oxford

The dominant residential form in Oxford is the single-detached house, which accounts for almost 90% of all units within the neighbourhood.

What we see in Oxford

In Oxford the drywall work is settling cracks/nail pops, basement development, builder-grade L4->L5 upgrades. We confirm what your home actually needs on site, in writing, before anything starts.

Pot lights, and which ones can be covered

Not all fixtures are equal

Older recessed fixtures in Oxford ceilings need clearance and cannot be buried. Newer IC-rated fixtures are built to be in contact with insulation.

What we check

We identify what is installed before blowing. Where fixtures cannot be covered, they need boxing or replacing — and each one is also a significant air leak, so they are usually the first thing sealed regardless of type.

Ventilation is not optional up there

Cold attic, by design

An Oxford attic is meant to run close to outdoor temperature so the roof deck stays cold and snow does not melt and refreeze at the eaves.

The failure it prevents

Blocking soffit vents with insulation causes exactly the ice damming people add insulation to prevent. Air sealing the ceiling below and keeping the vents clear are two halves of the same job.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Oxford attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

Attics over additions and vaulted areas

The awkward spaces

An Oxford addition often has a shallow attic, a cathedral section or a knee wall, and those areas are where insulation is thinnest and access is worst.

Why they matter disproportionately

They are frequently the coldest rooms in the house, and they are the parts a general top-up misses because the blower cannot reach them. We look at them specifically rather than quoting an average depth across the whole ceiling.

Depth is the whole number

What you are buying

Attic performance is almost entirely a function of settled depth and even coverage. Two attics with the same product can perform very differently.

How we handle it

Depth markers are set before blowing so the result is measurable rather than asserted, and the Oxford attic is checked at the corners rather than only where the hatch is. An attic that is deep in the middle and thin at the perimeter is the usual finding.

How it works

Simple, clean, on schedule — Attic Insulation in Oxford Edmonton

Free quote

We come out to your Oxford Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Oxford Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Oxford Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Oxford Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Oxford Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Oxford Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Oxford Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Oxford Edmonton

Attic Insulation Oxford Edmonton: your questions answered

How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.
How much will this save me on heating?: We will not put a percentage on it. Too much depends on your air leakage, windows and furnace. We will tell you what depth you have now, what you would have after, and where the leaks are — those we can actually measure.
Cellulose or fibreglass?: Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Oxford Edmonton

Blown-in attic insulation in Oxford, sealed before it is filled