Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

I store things in my attic. Can I keep doing that?

Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.

Do you insulate the attic hatch too?

Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.

Cellulose or fibreglass?

Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.

How do I know I got the depth I paid for?

We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.

Why does my Keswick Area attic frost up in winter?

Almost always warm moist air leaking up from the house through pot lights, top plates or the hatch, then condensing on cold sheathing. More insulation on its own does not fix it — the leaks have to be sealed first.

Attic Insulation Keswick Area Edmonton | Attic Top-Up

Attic top-ups in Keswick Area that hold their depth

The most common mistake in an Keswick Area attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Depth markers left in place so the result is verifiable
Attic hatch insulated and weatherstripped
Existing insulation levelled before the top-up
Air sealing at pot lights, top plates and the attic hatch
Blown-in loose-fill to the depth your permit specifies
Baffles kept clear so the soffit vents still breathe

Ice damming and what the attic has to do with it

A heat problem, not a gutter problem

Ice at the eaves on an Keswick Area roof usually means heat is escaping into the attic, melting snow on the upper roof, and that meltwater refreezing over the cold overhang.

Where the fix actually is

More heat tape rarely solves it. Sealing the air leaks and getting even insulation coverage right out to the eaves is what lowers the deck temperature. That is why we look at the attic when someone calls about ice, not at the roofline.

Keeping the eaves clear in an Keswick Area attic

Ventilation and insulation are not opposites

An attic needs air moving from the soffits up to the ridge. Blowing loose-fill right into the eaves blocks that path, and a blocked attic gets damp regardless of how much insulation is in it.

Baffles

Baffles hold the insulation back so the soffit vents stay open. In older Keswick Area homes they are often missing entirely, which is why the corners look thin — someone deliberately kept the insulation back, or it was never installed to the edge.

The eaves are where it goes thin

Geometry works against you

The roof meets the wall at the lowest point in the attic, so there is least room for insulation exactly where the wall below needs it most.

What it needs

Baffles that hold the insulation back from the soffit vents while still letting depth carry out over the wall plate. Skipping them in an Keswick Area attic either blocks the venting or leaves a cold band above every exterior wall.

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Keswick Area attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

Why air sealing comes before insulation in Keswick Area

Insulation does not stop air

Batt and loose-fill slow heat transfer; neither stops air movement. In an Keswick Area attic warm moist household air rises through pot lights, top plates and the hatch, passes straight through the insulation and condenses when it hits the cold deck.

What that looks like later

Frost on the underside of the sheathing in February, then staining on the ceiling in spring. Sealing the penetrations first is the difference between insulation that works and insulation that becomes the problem.

What we can and cannot tell you about savings

Honest about the number

We will not quote you a percentage off your heating bill. It depends on your current depth, your air leakage, your windows, your furnace and how you heat the house.

What we will say

What the attic has now, what it would have after, and where the leaks are. Those are things we can measure and show you. A savings figure from a contractor who has not seen your utility bills is a sales number, not an estimate.

How it works

Simple, clean, on schedule — Attic Insulation in Keswick Area Edmonton

Free quote

We come out to your Keswick Area Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Keswick Area Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Keswick Area Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Keswick Area Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Keswick Area Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Keswick Area Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Keswick Area Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Keswick Area Edmonton

Attic Insulation Keswick Area Edmonton: your questions answered

Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
I store things in my attic. Can I keep doing that?: Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.
Do you insulate the attic hatch too?: Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.
Cellulose or fibreglass?: Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.
How do I know I got the depth I paid for?: We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.
Why does my Keswick Area attic frost up in winter?: Almost always warm moist air leaking up from the house through pot lights, top plates or the hatch, then condensing on cold sheathing. More insulation on its own does not fix it — the leaks have to be sealed first.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Keswick Area Edmonton

Attic top-ups in Keswick Area that hold their depth