Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

I store things in my attic. Can I keep doing that?

Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.

How do I know I got the depth I paid for?

We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.

Do you insulate over an addition or a vaulted ceiling?

Those need looking at specifically rather than quoting an average depth. Shallow attics, cathedral sections and knee walls are usually the coldest rooms in an Fraser house and the parts a general top-up misses.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

Attic Insulation Fraser Edmonton | Attic Top-Up

Blown-in attic insulation in Fraser, sealed before it is filled

The most common mistake in an Fraser attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Depth markers left in place so the result is verifiable
Existing insulation levelled before the top-up
Air sealing at pot lights, top plates and the attic hatch
Blown-in loose-fill to the depth your permit specifies
Attic hatch insulated and weatherstripped
Baffles kept clear so the soffit vents still breathe

Adding to what is already there

You rarely start empty

Most Fraser attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

Fraser drywall in context

About Fraser

Named for John Fraser, an original homesteader in the area and one of the first trustees of the Belmont School, Fraser is located in the City's far northwest.

What we see in Fraser

In Fraser the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Ventilation is not optional up there

Cold attic, by design

An Fraser attic is meant to run close to outdoor temperature so the roof deck stays cold and snow does not melt and refreeze at the eaves.

The failure it prevents

Blocking soffit vents with insulation causes exactly the ice damming people add insulation to prevent. Air sealing the ceiling below and keeping the vents clear are two halves of the same job.

Depth is the whole number

What you are buying

Attic performance is almost entirely a function of settled depth and even coverage. Two attics with the same product can perform very differently.

How we handle it

Depth markers are set before blowing so the result is measurable rather than asserted, and the Fraser attic is checked at the corners rather than only where the hatch is. An attic that is deep in the middle and thin at the perimeter is the usual finding.

The attic hatch, which everybody forgets

A hole in the ceiling

The hatch in an Fraser home is often an uninsulated panel sitting in a frame with no weatherstrip. It is a direct opening between the house and a space that is at outdoor temperature.

What we do

The hatch gets insulated on its back face and weatherstripped so it seals when closed. It is a small job that shows up disproportionately in comfort, and it is the first place we look when someone says the hallway is cold.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Fraser attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

The eaves are where it goes thin

Geometry works against you

The roof meets the wall at the lowest point in the attic, so there is least room for insulation exactly where the wall below needs it most.

What it needs

Baffles that hold the insulation back from the soffit vents while still letting depth carry out over the wall plate. Skipping them in an Fraser attic either blocks the venting or leaves a cold band above every exterior wall.

How it works

Simple, clean, on schedule — Attic Insulation in Fraser Edmonton

Free quote

We come out to your Fraser Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Fraser Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Fraser Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Fraser Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Fraser Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Fraser Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Fraser Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Fraser Edmonton

Attic Insulation Fraser Edmonton: your questions answered

Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.
I store things in my attic. Can I keep doing that?: Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.
How do I know I got the depth I paid for?: We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.
Do you insulate over an addition or a vaulted ceiling?: Those need looking at specifically rather than quoting an average depth. Shallow attics, cathedral sections and knee walls are usually the coldest rooms in an Fraser house and the parts a general top-up misses.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.
Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Fraser Edmonton

Blown-in attic insulation in Fraser, sealed before it is filled