Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

How much will this save me on heating?

We will not put a percentage on it. Too much depends on your air leakage, windows and furnace. We will tell you what depth you have now, what you would have after, and where the leaks are — those we can actually measure.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Will insulating my attic stop the ice at my eaves?

Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.

Cellulose or fibreglass?

Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.

Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Attic Insulation Fort Saskatchewan | Attic Top-Up

Attic insulation in Fort Saskatchewan: air seal first, then blow

The most common mistake in an Fort Saskatchewan attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Air sealing at pot lights, top plates and the attic hatch
Existing insulation levelled before the top-up
Baffles kept clear so the soffit vents still breathe
Attic hatch insulated and weatherstripped
Depth markers left in place so the result is verifiable
Blown-in loose-fill to the depth your permit specifies

Keeping the eaves clear in an Fort Saskatchewan attic

Ventilation and insulation are not opposites

An attic needs air moving from the soffits up to the ridge. Blowing loose-fill right into the eaves blocks that path, and a blocked attic gets damp regardless of how much insulation is in it.

Baffles

Baffles hold the insulation back so the soffit vents stay open. In older Fort Saskatchewan homes they are often missing entirely, which is why the corners look thin — someone deliberately kept the insulation back, or it was never installed to the edge.

The eaves are where it goes thin

Geometry works against you

The roof meets the wall at the lowest point in the attic, so there is least room for insulation exactly where the wall below needs it most.

What it needs

Baffles that hold the insulation back from the soffit vents while still letting depth carry out over the wall plate. Skipping them in an Fort Saskatchewan attic either blocks the venting or leaves a cold band above every exterior wall.

Ventilation is not optional up there

Cold attic, by design

An Fort Saskatchewan attic is meant to run close to outdoor temperature so the roof deck stays cold and snow does not melt and refreeze at the eaves.

The failure it prevents

Blocking soffit vents with insulation causes exactly the ice damming people add insulation to prevent. Air sealing the ceiling below and keeping the vents clear are two halves of the same job.

Cellulose against fibreglass in an Fort Saskatchewan attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

Why air sealing comes before insulation in Fort Saskatchewan

Insulation does not stop air

Batt and loose-fill slow heat transfer; neither stops air movement. In an Fort Saskatchewan attic warm moist household air rises through pot lights, top plates and the hatch, passes straight through the insulation and condenses when it hits the cold deck.

What that looks like later

Frost on the underside of the sheathing in February, then staining on the ceiling in spring. Sealing the penetrations first is the difference between insulation that works and insulation that becomes the problem.

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Fort Saskatchewan attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

How it works

Simple, clean, on schedule — Attic Insulation in Fort Saskatchewan

Free quote

We come out to your Fort Saskatchewan property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Fort Saskatchewan starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Fort Saskatchewan. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Fort Saskatchewan home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Fort Saskatchewan. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Fort Saskatchewan Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Fort Saskatchewan trusts for repair, restoration and finishing — rated on Google by Fort Saskatchewan homeowners.

Read the reviews, or leave your own after your attic insulation project in Fort Saskatchewan.

Read our reviews on Google

FAQ — Attic Insulation Fort Saskatchewan

Attic Insulation Fort Saskatchewan: your questions answered

Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
How much will this save me on heating?: We will not put a percentage on it. Too much depends on your air leakage, windows and furnace. We will tell you what depth you have now, what you would have after, and where the leaks are — those we can actually measure.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.
Will insulating my attic stop the ice at my eaves?: Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.
Cellulose or fibreglass?: Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.
Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Fort Saskatchewan

Attic insulation in Fort Saskatchewan: air seal first, then blow