Why is the area above my exterior walls always cold?

Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Can I add over the old insulation?

Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.

Will insulating my attic stop the ice at my eaves?

Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Do I need to seal before adding insulation?

Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Attic Insulation Cy Becker Edmonton | Attic Top-Up

Attic top-ups in Cy Becker that hold their depth

The most common mistake in an Cy Becker attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Blown-in loose-fill to the depth your permit specifies
Air sealing at pot lights, top plates and the attic hatch
Depth markers left in place so the result is verifiable
Baffles kept clear so the soffit vents still breathe
Attic hatch insulated and weatherstripped
Existing insulation levelled before the top-up

Depth is the whole number

What you are buying

Attic performance is almost entirely a function of settled depth and even coverage. Two attics with the same product can perform very differently.

How we handle it

Depth markers are set before blowing so the result is measurable rather than asserted, and the Cy Becker attic is checked at the corners rather than only where the hatch is. An attic that is deep in the middle and thin at the perimeter is the usual finding.

Ventilation is not optional up there

Cold attic, by design

An Cy Becker attic is meant to run close to outdoor temperature so the roof deck stays cold and snow does not melt and refreeze at the eaves.

The failure it prevents

Blocking soffit vents with insulation causes exactly the ice damming people add insulation to prevent. Air sealing the ceiling below and keeping the vents clear are two halves of the same job.

Keeping the eaves clear in an Cy Becker attic

Ventilation and insulation are not opposites

An attic needs air moving from the soffits up to the ridge. Blowing loose-fill right into the eaves blocks that path, and a blocked attic gets damp regardless of how much insulation is in it.

Baffles

Baffles hold the insulation back so the soffit vents stay open. In older Cy Becker homes they are often missing entirely, which is why the corners look thin — someone deliberately kept the insulation back, or it was never installed to the edge.

Insulating a Cy Becker attic with knob-and-tube or old wiring

Stop and check first

Some older Cy Becker homes still carry active knob-and-tube wiring in the attic. Burying it in insulation is not something we do — it needs an electrician to assess and usually to replace before the attic is filled.

Why we raise it

It is the kind of thing found halfway through a job, and it is far cheaper to find at the quote. If we see it, we tell you and we stop until it is dealt with.

Bathroom and kitchen fans venting into the attic

Found more often than you would think

In older Cy Becker homes a bathroom fan is frequently ducted into the attic space rather than through the roof or soffit. It dumps warm wet air straight into the coldest part of the house.

Why it matters before insulating

Burying that under fresh loose-fill hides a moisture source that will show up as frost and staining. If we find one we tell you, because it needs correcting first — insulation on top of it makes it harder to reach and harder to diagnose.

Cellulose against fibreglass in an Cy Becker attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

How it works

Simple, clean, on schedule — Attic Insulation in Cy Becker Edmonton

Free quote

We come out to your Cy Becker Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Cy Becker Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Cy Becker Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Cy Becker Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Cy Becker Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Cy Becker Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Cy Becker Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Cy Becker Edmonton

Attic Insulation Cy Becker Edmonton: your questions answered

Why is the area above my exterior walls always cold?: Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.
Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
Will insulating my attic stop the ice at my eaves?: Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
Do I need to seal before adding insulation?: Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Cy Becker Edmonton

Attic top-ups in Cy Becker that hold their depth