I store things in my attic. Can I keep doing that?

Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.

My bathroom fan seems to vent into the attic. Is that a problem?

Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.

How do I know I got the depth I paid for?

We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.

Cellulose or fibreglass?

Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.

Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

Do I need to seal before adding insulation?

Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Attic Insulation Callaghan Edmonton | Attic Top-Up

Attic insulation in Callaghan: air seal first, then blow

The most common mistake in an Callaghan attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Blown-in loose-fill to the depth your permit specifies
Depth markers left in place so the result is verifiable
Air sealing at pot lights, top plates and the attic hatch
Attic hatch insulated and weatherstripped
Baffles kept clear so the soffit vents still breathe
Existing insulation levelled before the top-up

Depth is the whole number

What you are buying

Attic performance is almost entirely a function of settled depth and even coverage. Two attics with the same product can perform very differently.

How we handle it

Depth markers are set before blowing so the result is measurable rather than asserted, and the Callaghan attic is checked at the corners rather than only where the hatch is. An attic that is deep in the middle and thin at the perimeter is the usual finding.

The attic hatch, which everybody forgets

A hole in the ceiling

The hatch in an Callaghan home is often an uninsulated panel sitting in a frame with no weatherstrip. It is a direct opening between the house and a space that is at outdoor temperature.

What we do

The hatch gets insulated on its back face and weatherstripped so it seals when closed. It is a small job that shows up disproportionately in comfort, and it is the first place we look when someone says the hallway is cold.

Cellulose against fibreglass in an Callaghan attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

Insulating a Callaghan attic with knob-and-tube or old wiring

Stop and check first

Some older Callaghan homes still carry active knob-and-tube wiring in the attic. Burying it in insulation is not something we do — it needs an electrician to assess and usually to replace before the attic is filled.

Why we raise it

It is the kind of thing found halfway through a job, and it is far cheaper to find at the quote. If we see it, we tell you and we stop until it is dealt with.

Pot lights, and which ones can be covered

Not all fixtures are equal

Older recessed fixtures in Callaghan ceilings need clearance and cannot be buried. Newer IC-rated fixtures are built to be in contact with insulation.

What we check

We identify what is installed before blowing. Where fixtures cannot be covered, they need boxing or replacing — and each one is also a significant air leak, so they are usually the first thing sealed regardless of type.

The attic hatch nobody insulates

A hole in the ceiling

An uninsulated, unsealed hatch is a direct opening between the heated house and a cold attic, and it is often the single worst detail in an otherwise good Callaghan ceiling.

Simple fix

An insulated cover with weatherstripping and a dam around the opening so blown insulation does not spill through when it is opened.

How it works

Simple, clean, on schedule — Attic Insulation in Callaghan Edmonton

Free quote

We come out to your Callaghan Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Callaghan Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Callaghan Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Callaghan Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Callaghan Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Callaghan Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Callaghan Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Callaghan Edmonton

Attic Insulation Callaghan Edmonton: your questions answered

I store things in my attic. Can I keep doing that?: Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.
My bathroom fan seems to vent into the attic. Is that a problem?: Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.
How do I know I got the depth I paid for?: We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.
Cellulose or fibreglass?: Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.
Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
Do I need to seal before adding insulation?: Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Callaghan Edmonton

Attic insulation in Callaghan: air seal first, then blow