How much insulation should my Boyle Street attic have?

The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.

Do I need to seal before adding insulation?

Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Do you insulate the attic hatch too?

Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.

Do you insulate over an addition or a vaulted ceiling?

Those need looking at specifically rather than quoting an average depth. Shallow attics, cathedral sections and knee walls are usually the coldest rooms in an Boyle Street house and the parts a general top-up misses.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Attic Insulation Boyle Street Edmonton | Attic Top-Up

Attic insulation in Boyle Street: air seal first, then blow

The most common mistake in an Boyle Street attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Existing insulation levelled before the top-up
Blown-in loose-fill to the depth your permit specifies
Attic hatch insulated and weatherstripped
Baffles kept clear so the soffit vents still breathe
Air sealing at pot lights, top plates and the attic hatch
Depth markers left in place so the result is verifiable

Storage in the attic and the insulation you lose

Boards over joists compress everything

Where a Boyle Street homeowner has laid plywood across the joists for storage, the insulation beneath is squashed to joist depth. That strip performs at a fraction of the rest of the attic.

Options

Either the storage area is raised on a platform above the finished insulation depth, or it is accepted as a deliberately weaker zone kept as small as possible. What does not work is topping up around it and pretending the platform is not there.

Boyle Street drywall in context

About Boyle Street

The hub of Edmonton's early commercial district, Boyle Street was recorded on a map of the newly created town of Edmonton in 1892.

What we see in Boyle Street

In Boyle Street the drywall work is verify dominant band before writing notes. We confirm what your home actually needs on site, in writing, before anything starts.

Pot lights, and which ones can be covered

Not all fixtures are equal

Older recessed fixtures in Boyle Street ceilings need clearance and cannot be buried. Newer IC-rated fixtures are built to be in contact with insulation.

What we check

We identify what is installed before blowing. Where fixtures cannot be covered, they need boxing or replacing — and each one is also a significant air leak, so they are usually the first thing sealed regardless of type.

Insulating a Boyle Street attic with knob-and-tube or old wiring

Stop and check first

Some older Boyle Street homes still carry active knob-and-tube wiring in the attic. Burying it in insulation is not something we do — it needs an electrician to assess and usually to replace before the attic is filled.

Why we raise it

It is the kind of thing found halfway through a job, and it is far cheaper to find at the quote. If we see it, we tell you and we stop until it is dealt with.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Boyle Street attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

Depth is the whole number

What you are buying

Attic performance is almost entirely a function of settled depth and even coverage. Two attics with the same product can perform very differently.

How we handle it

Depth markers are set before blowing so the result is measurable rather than asserted, and the Boyle Street attic is checked at the corners rather than only where the hatch is. An attic that is deep in the middle and thin at the perimeter is the usual finding.

What we can and cannot tell you about savings

Honest about the number

We will not quote you a percentage off your heating bill. It depends on your current depth, your air leakage, your windows, your furnace and how you heat the house.

What we will say

What the attic has now, what it would have after, and where the leaks are. Those are things we can measure and show you. A savings figure from a contractor who has not seen your utility bills is a sales number, not an estimate.

How it works

Simple, clean, on schedule — Attic Insulation in Boyle Street Edmonton

Free quote

We come out to your Boyle Street Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Boyle Street Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Boyle Street Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Boyle Street Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Boyle Street Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Boyle Street Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Boyle Street Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Boyle Street Edmonton

Attic Insulation Boyle Street Edmonton: your questions answered

How much insulation should my Boyle Street attic have?: The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.
Do I need to seal before adding insulation?: Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
Do you insulate the attic hatch too?: Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.
Do you insulate over an addition or a vaulted ceiling?: Those need looking at specifically rather than quoting an average depth. Shallow attics, cathedral sections and knee walls are usually the coldest rooms in an Boyle Street house and the parts a general top-up misses.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Boyle Street Edmonton

Attic insulation in Boyle Street: air seal first, then blow