Can I add over the old insulation?

Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.

Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

Can you blow insulation over my pot lights?

Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.

My bathroom fan seems to vent into the attic. Is that a problem?

Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.

Do I need to seal before adding insulation?

Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Attic Insulation Bergman Edmonton | Attic Top-Up

Attic top-ups in Bergman that hold their depth

The most common mistake in an Bergman attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Air sealing at pot lights, top plates and the attic hatch
Blown-in loose-fill to the depth your permit specifies
Existing insulation levelled before the top-up
Depth markers left in place so the result is verifiable
Baffles kept clear so the soffit vents still breathe
Attic hatch insulated and weatherstripped

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Bergman attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

Bergman drywall in context

About Bergman

Bergman was one neighbourhood that made up the area called Beverly.

What we see in Bergman

In Bergman the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Bergman attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

Ventilation is not optional up there

Cold attic, by design

An Bergman attic is meant to run close to outdoor temperature so the roof deck stays cold and snow does not melt and refreeze at the eaves.

The failure it prevents

Blocking soffit vents with insulation causes exactly the ice damming people add insulation to prevent. Air sealing the ceiling below and keeping the vents clear are two halves of the same job.

What we can and cannot tell you about savings

Honest about the number

We will not quote you a percentage off your heating bill. It depends on your current depth, your air leakage, your windows, your furnace and how you heat the house.

What we will say

What the attic has now, what it would have after, and where the leaks are. Those are things we can measure and show you. A savings figure from a contractor who has not seen your utility bills is a sales number, not an estimate.

Insulating a Bergman attic with knob-and-tube or old wiring

Stop and check first

Some older Bergman homes still carry active knob-and-tube wiring in the attic. Burying it in insulation is not something we do — it needs an electrician to assess and usually to replace before the attic is filled.

Why we raise it

It is the kind of thing found halfway through a job, and it is far cheaper to find at the quote. If we see it, we tell you and we stop until it is dealt with.

Pot lights, and which ones can be covered

Not all fixtures are equal

Older recessed fixtures in Bergman ceilings need clearance and cannot be buried. Newer IC-rated fixtures are built to be in contact with insulation.

What we check

We identify what is installed before blowing. Where fixtures cannot be covered, they need boxing or replacing — and each one is also a significant air leak, so they are usually the first thing sealed regardless of type.

How it works

Simple, clean, on schedule — Attic Insulation in Bergman Edmonton

Free quote

We come out to your Bergman Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Bergman Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Bergman Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Bergman Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Bergman Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Bergman Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Bergman Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Bergman Edmonton

Attic Insulation Bergman Edmonton: your questions answered

Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
Can you blow insulation over my pot lights?: Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.
My bathroom fan seems to vent into the attic. Is that a problem?: Yes, and it needs correcting before insulating. It dumps warm wet air into the coldest part of the house, and burying it under fresh insulation hides a moisture source that will show up later as frost and staining.
Do I need to seal before adding insulation?: Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Bergman Edmonton

Attic top-ups in Bergman that hold their depth